MDB7851AWW41 Maytag Dishwasher - Instructions

Removed assembly holding the docking station to insure the passageway was clear. I reversed the flappers and noticed an improvement in cleaning then decided to order a new part. Installation was simple and the repair seems to have worked well.

Removed top tray. Removed old wash arm (rotating) and installed new one using a screw driver.

Manualy un-snapped station docking (w/flapper) and removed. Snapped in new one.

I removed the old rack adjuster by unscrewing four screws. I put the new rack adjuster in place, carefully fitted the adjustment parts together, then replaced the four screws. The best part of the repair was that Parts Select had originally indicated that my part would be on back order for a few weeks, but I actually received the part within just a few days. What a nice surprise - thanks!

Open door fully. Remove all screws that hold inside panel to Front panel. Carefully remove Inside panel being VERY CAREFULL not to pull wiring out of door switch [top of door] and operator switch panel [also top of door]. Remove door switch, next remove 3 screws holding switch panel in place. Remove the top plastic section where switch panel mounts and set aside. Carefully remove green ground wire from bottem hinge for door. [right side] Next CAREFULLY remove front panel from hinges using EXTREME CARE not to let hinges "free fall" to the open position. Remove old panel. Install new panel in the reverse order as the old one was removed. DO NOT PANIC if you happen to pull the "ribbon cable' out of panel switch. It will plug back in very quickly and only one way. Just make sure it is "seated" in plug. The "key word" for this panel replacement is CAREFULLY.

threw out the broken and put in a fantastically improved new one. very easy (would have done it sooner if I'd known it was that simple to find it online and order it) thanks

Snapped out the old retainer, snapped in the new. Then snapped in the washer arm. Done. Works great.

Basically took out of box and put in dishwasher.

Very simple! First, free the wheel from the rail - should come right out if the wheel is broken. Then click the wheel base off the small shelf rod by rotating the wheel bse. Then, click the rail end cap off the rail by pressing it through the small square hole in the flat side of the rail. Insert the wheel into the rail, then click the wheel base back onto the shelf rail rod where you took the old one off. Click the rail end cap back on, and you're done!

Removed the bottom tray. Removed the two clips in the top tray guides and removed the top tray. Removed the top spray arm and transfer tube by unclipping it from the top and at the back and then rotated it down and out. Removed the six screws around the upper pump housing and removed it along with the bottom spray arm. Removed the three screws holding the filter protector plate and removed it. Removed the two screws holding the accumulator / flow plate and removed it. Put it back together in reverse order careful to not over tighten the screws.

I unscrewed the old rack adjuster assembly and screwed the new one on (this was after I took the rack out of the diswasher) -- I actually saved one of the old intact plastic wheels for future repairs.

Initially ordered the rack adjuster assembly, not realizing that I would also need the adjuster lever and adjuster cover, too. This piece is NOT what originally came with our unit. The line drawing for part 17 shows what our unit looks like. That part has apparently been discontinued and we were guided by Maytag to order this substitution, which is actually a Whirlpool part. Thought someone else might want to know this if they happen to have the same series of Maytag DW as we do. It fits well onto the rack, however, the location of the wheels on the unit are different than the original which means that the middle rack now slides out of the dishwasher about 3" less than it used to, which is kind of a bummer. All that said, the repair was a piece of cake and the hubs on the wheels are now metal instead of the original plastic. . .I expect this part to last a good long while!

I noticed that the dishes on the top rack were not getting clean. While the dishwasher was running, I opened the door to see if the arms were moving/spraying and they were not. I cleaned the filter and checked the impeller and both were clean and not damaged. After looking how the top rack slides into the "flapper" I took it off to inspect it. It was missing the rubber to make the seal with the tube from the top rack. After replacing this part, the dishwasher is cleaning like new. Here is the part PS2340934 Docking Station with Flappers

Unscrewed dishwasher from counter and pulled it out from under the counter a few inches. Looked at the side of the dishwasher with the remaining good spring and saw how it was attached: One end was hooked to a little tether strung around a pulley, the other to one of a few steel slots. Copied that side for the new spring and works fine now.

1.Disconnected the electricty 2. pulled the dishwasher from under the cabinet 3. tilted the washer on it's face (water supply was long enough and did not need to disconnected.)4. unscrerwed the 2 plastic nuts that hold the heating eliment in place. 5. tilted the dishwasher back upright and removed the old heating element. 6.put the new part in place had a helper tilt the washer forward while i tightened up the two plastic nuts to hold the part in place.7 reattached the elecrtic conectors to the heating element. 8. pushed the dishwasher back in place. 9 hook the electricity back up. During step 4 i had to remove the electric connectors from the old heating element.

Wanted to change our dishwasher to a stainless steel appearance. When the panel was delivered in 1 day I might add it was flawless. I removed the old panel and the new panel attached to the dishwasher perfectly with the screw holes exactly lining up. The most inexpensive way to turn a kitchen into a stainless steel appliance look.