MDB7759SAB2 Maytag Dishwasher - Instructions

I Removed the upper wash rack by removing locks on each front slide of rack. I laid a towel in the bottom of the washer to keep anything dropped, retrievable. I then removed the top screw closest to the spinner location. I then carefully pulled down on the mounting, which exposed the bad bushing lock. I removed the old bushing lock and replaced with new one. I then replaced the spinner with a push with one hand while holding the bushing in place with the other hand. You will feel a snap as all goes into place. Make sure new spinner spins freely. Now reinstall removed screw. Do not over tighten. Now reinstall lower rack, carefully aligning water feed in rear of washer, and making sure all rollers are back in sliding rack. Reinstall locking tabs onto sliding rack. Now slide out rack, it should not come off slider. Important: now remove the towel in the bottom of the washer. If left in place, you will have a fire during the drying cycle. Close the door and test your washer through a cycle. I felt confident and did a load of dishes. If all went well, spinner should be in place, not in the bottom of the washer.

I opened the package took out the replacement part and installed it with no tools. Easy, done in 10 minutes.

First I got online to troubleshoot issue to save mysel from a service call. One of the first UTube videos, a young man said usually the main issue was the lever. He pushed down on the floater. If it didn't click, than the lever below needed to be replaced. Most important to turn off the circuit breaker before beginning the repair. I got on whirlpool.com, Part Select, ordered the lever, which was under $10. And once delivered, was able to switch out the old lever with the new replacement. Part Quote video took me through the process step by step. The lever package was marked that usually it was only 2% of the time that replacing the lever fixed the issue. Of course, I was thrilled, my dishwasher was up and running again. Thank you.

With a little pressure, I was able to push off the broken wheel pieces with my thumbs. I was able to snap on the new wheel pieces really easily.
This job took less than 15 minutes to replace all 4 wheel pieces.

First, I bought the door balance link to replace the broken links that connect to the springs.

Because I didn't have enough slack to simply pull out the dishwasher far enough to reach the springs, I had to disconnect the water line and electrical wiring.
The only reason my repair took as long as it did was because there was so little room underneath the dishwasher for disconnecting the water line. I had to buy a shorter adjustable wrench. Also, I had leaks after reconnecting the water line. I had to tighten the compression nut as far as it would go. The nut wrapped around a white substance that had been applied to the threads (I believe this is called pipe tape), which did the trick for sealing the leak.

The repair was a complete success! The parts arrived fast and the information from other customers on the the PartsSelect website was invaluable.

Follow the u tube instruction. Replacing the pump was very simple and easy. The hard part was getting the dishwasher out of the cabinet and back in again.

Disconnected the damaged hose extension from the dishwasher outlet drain hose and the connection to the sink drain. Removed two clamps. One a spring clamp and the other a screw clamps. Connected the new extension hose with a spring clamp to the dishwasher outlet drain hose. Connected the other end to the sink drain with a screw clamp. Checked for leaks. Good to go!

Pull the old seal out and push the new seal in. Done. Easy. The only issue is the door is still leaking and I have to replace the seal and the plate that goes across the bottom of the door.

Order both this seal and the seal for the bottom of the door at the same time.

Watch your video about my dishwasher symptoms. Move water tube for upper rack to the right and release lower spray arm. Remove 4 clutch head screws from filter cover and remove. Dig out 10 years of undisolved soap and reassemble.

I had to remove the baskets, spray assemblies (no tools needed) and disassemble the section of the pump that contained the chopper assembly. (removing three Torx screws)
I had to remove a part of the old chopper that had gone into the pump, but I was lucky that a magnet grabbed it so I didn't have to disassemble the pump.
The total repair was not difficult. The only problem was access (hands in the way while repairing difficult to see) and compressing the spring on the new chopper while trying to slip it into the groove.
The parts came in three days and they fit perfectly

First I would like to say I was concerned about undertaking a dishwasher repair ,as I now am legally blind and I was concerned that my vision impairment might cause me a problem. My dishwasher pump motor was not running and from the humming sound I could tell it was cycling power off on the thermo switch overload. The pump can be removed by turning it counter clockwise,however it would not move and I could not rotate the motor manually, IT appeared that the impeller must be jammed,so I removed the complete ascribe..After I removed it the motor still could not be removed for replacement. I ordered the complete assembly from PartSelect.com an was supervised how fast it was delivered. The hardest part was getting the seal to go in place as it was new and a tight fit. The Partsselect.com video's ,on repair instructions were very helpful. I reinstalled the dishwasher and everything worked fine.Thanks for thefast delivery of my order.

simply line up the new pin with the rectangular slot in the kick panel and metal panel behind, slide the pin in and turn it with a flat blade screw driver.
NOTE: the original pin was black. A black replacement part cost $29 plus shipping! A knock-off pin was only $6 plus shipping. I got the cheap one and colored it with a black Sharpee marker before installation.

After looking at what everyone else had done, I decide that I would take the dishwasher out of the wall space and set it on its side. This require me to turn off the power first. Then I pull the diswasher out from its space in the wall. I turned off the the water and then took off the water hose, then took of the return hose. There was water left in both, so there was a little water on the floor as a result of this. Then I finally pulled out the unit and laid it down on its side. The motor was very visible and was easy to access. The hardest part was finding the bolt to take it off. I pulled off the power connector to the motor and then took off the one bolt that was holding the motor on the washer. Then I twisted the motor, but it would not come off. I finally got a screw driver and put it in the small opening between the motor and the connection and it finally came off. This took all of about 30 minutes. Once I got the motor off, I notice that the aluminum grating inside was dirty and needed cleaning. So I cleaned this and put it back inside. The new motor came with every thing, so I put it in and twisted it. Then put back in the bolt, reconnected the power cable, put back on the water and reconnected the output cable. In order to make sure there were no leaks before I put it back in for good, I ran a short wash to check to see if everything was tight. There were no leaks, so I put everything back in the wall. It really did sound very nice now. This dishwasher unit came with noise padding, so I put that back as well. The dishwasher, now is very quite and I don't mind it running any time during the day. The hardest part about this is getting the motor off and find the bolt. It is down between motor and the unit and there was some aluminum between this and the dishwasher, so you need a long nutdriver to get it off.

Due to the way I installed the appliance originally it was not necessary to disconnect supply water nor the drain connections. When the cord broke the spring came out of the point of connection to the appliance. It some "finagelling" to reattach the spring.After some "select vocabulary" it hooked into the correct spot and the rest was history.

Turned off the power at the breaker, turned off the water supply, disconnected the water line, removed all three racks, pulled dishwasher out from under the counter, laid the unit on its back, removed the flat plastic water lines from inside the dishwasher, disconnected the hose and all wires (plugs) that were attached to the motor & pump assembly, removed three plastic wedges that held the pump assembly to the bottom of the dishwasher, tried to remove the motor & pump assembly from the inside of the dishwasher but it wouldn't fit through the hole, removed two parts from the motor a silver cylinder with two wires attached to it and a white plastic piece with copper wound wires and magnets in it so that it would fit, once the entire assembly was out removed one screw that holds the motor to the plastic pump assembly, twisted the motor counter clockwise the pulled it straight off, after installing the new motor I removed the silver cylinder (maybe a capacitor) that was attached to the motor leaving the two wires attached to it so that the assembly would fit through the hole in the bottom of the dishwasher, cleaned the rim of the hole and the rubber gasket on the assembly, put the assembly through the hole in the bottom of the dishwasher, installed the three wedges to hold it in place, then put it all back together. When I ran the dishwasher it was as quiet as when it was new.