MDB7851AWS0 Maytag Dishwasher - Instructions

Not being very computer literate, the most difficult part of the entire venture was navigating your web site. But I finally found the part I needed. I paid on line with a credit card, and received the part within a few days. I popped it in the dishwasher, and it took three days before my son noticed it.
He was surprised and I was proud to say " I ordered it on line."
All's well that end's well.
I would difinately use your service again.

disconnected unit (electrical, water, and waste) un mounted from countertop, removed from under countertop, unscrewed hose clamb, cut off wire tie. Attached new hose and wire tie (not included) reversed above steps. Done in about 15 minutes

I unscrewed the door panel. removed the plastic cover protecting the dispenser. unscrewed the dispenser (6 screws). I removed the old dispenser and put the new one on and put it all back together. It was pretty easy.

This isn't a how to fix it....it's what part was bad. I had originally contacted the local Maytag repair center and the owner swore up and down that our problem had to be the thermostat and not the heater. He said he had only replaced maybe 5 heaters in 15 years. But our heater looked like heck, with hard water deposits and all, and it wasn't that old, but we went ahead and ordered the thermostat from PartSelect, which came in a day. The problem wasn't the thermostat, so we ordered the heater from PartSelect (again, only one day delivery) and our dishwasher is working again. The heater coil actually had a hole in it from some sort of corrosion. My 18-year-old son did the repair job in a jiffy.

Used torx bit to remove screws on door and removed the back of door. Removed wiring from switches (2) on broken latch and removed latch. Plugged in switches on new latch and placed latch in position. Screwed back of door into place and that was it! Very simple task and new latch looks and feels much more sturdy than old one.

All that was broken on the old detergent dispenser was the door but the door can not be ordered without buying the whole detergent/rinse aid assembly. When I got the new item I just removed the old door and replaced it with the new door that I had taken off the new one. I still have the new detergent/rinse aid assembly that I can keep if I need to change it in the future.

Turn-off the dishwasher power at the circuit breaker. Open the dishwasher door flat. Remove the 11 screws around the perimeter of the door using a t-20 torx bit (available at any hardware store). The latch assembly is held on by the top middle two door screws. Pull latch assembly out from top of door. Remove the black and white cable assembly connectors from the latch assembly making sure to note which side each color is on. If you have trouble sliding the connector off, use a flat screwdriver carefully to pry it, but do not pull on the wires. Install cable connectors onto new latch assembly making making sure the black and white cables are on the correct sides. Position the door at a 45 degree angle and place the latch assembly into position while putting the white inner door over it. Reinstall the 11 torx screws around the side of the door being sure the screws are snug, but not overtightened. Test the operation of your dishwasher. The new latch assembly seems to be built better than the factory original.

Removed the basketsThen removed the bottom spray arm with nut driver. Removed the cover and spray tower assembly. removed screw holding broken impeller. Replaced and reversed process. Really easy. As an aside. This dishwasher has been a major disappointment. lots of things not holding up. Didn't go cheap when buying it. Nice to find a site with good prices for parts

1. Fully opened door of dishwasher.
2. With star driver, removed 11 screws from the insde edge of door.
3. Outside front panel of door then is separated from inside panel slightly to again access to, latch assembly.
4. Verified that replacement part matched existing part.
5. Lifted out damaged latch assembly and disconnected the two electrical leads by gently pulling on the insulated connectors.
6. Connected the electrical leads to the coresponding connections on the new part and replaced in the reverse order of above.
7. Total time for repair was 15 minutes.

The repair was as easy as 1, 2, 3.. 1) Open box that the new dishrack was shipped in from PartSelect. 2) Take old and dry rotted dishrack out of my dishwasher. 3) Place new dishrack into my dishwasher.

Less than 5 minutes.

First shut circuit breaker to dishwasher and close water valve under the sink. Remove the screws that hold the dishwasher to the counter, then remove the bottom cover plates. I slid the diswasher out almost all the way...On the left side bottom I could see the old water inlet valve was attached by 2 hex screws and a clip with 3 wires..after removing the 2 screws and clip I was able to remove the water line (place something to catch a small amount of water) and remove the black rubber hose from the old intake valve by squeezing the clip.. Removed the brass nut from the old valve you'll need it. I installed the new water inlet valve by connecting the old brass nut
(replace with new thread seal tape) , replace the water line and black rubber hose...attach to frame with the 2 hex screws and replace clip with wires...I slid the dishwasher back under the counter, turned the water on and power back on...I ran the dishwasher before I secured it in place to check for leaks...Dry as a bone...I then secured it to the counter and replaced the bottom plates.. the dishwasher is working like new...everything comes out spotless...Sometimes repairs are not as hard as they look, just take your time.

First I removed two bottom plates (two screws on each) Then I pulled dishwasher out about six inches. That's as far as it would go because I did not disconnect the water and drain hoses. That was enough to remove the broken cable and collect the disabled spring. I then reattached the new cable to the spring and reworked them into position. NOTE: There is a right and left cable and spring set-up. I used the "good" side as a guide. I then pushed the dishwasher back into place and replaced the two bottom plates.

removed the inside cover to the door,7 screws, removed the latch assembly, replaced with new parts, back in service.

I turned off the electricity at the circuit breaker. Sitting in a chair in front of the opened dishwasher with the partially opened door resting on my knees, I removed the 10 screws lining the inside of the door (setting them in order on the cabinet above -- 2 are different length so this helps keep them in order.
I tilted the inner cover on the door up (which is what the screws had been holding). With the door not fully open because it was on my knees, I was able to position the cover so that I did not have to remove the connection to the soap dispenser.
The two middle screws removed earlier were the screws that held the latch in place, so the assembly was already loose at this point. I put a black mark on the assembly to mark the side that the black wires were attached. Then with the pliers removed the plugs that were connected to the switches on either side of the assembly. Then marked the replacement assembly with the black mark on the same side as the one removed. I attached the plugs to the the replacement assembly using the black mark as reminder for which side was which.
I lined up the latch on the door where it goes, lowered the lid (lifting the lower edge over the base a little), lined up and started the latch screws (middle 2), then started all of the other screws and then tightened them all. Closed the lid and tested the latch. It was closing correctly now. I turned on the electricity and tested to make sure all was now working properly.

First I opened the breaker on the dishwasher removing power from the unit. Then I removed the Torx head screws on the cover on the back side of the front door. Then I pulled off the stainless steel sheet metal panel which exposed the door latch. Then I unplugged the electrical connectors to the two micro switches on the assembly, next I plugged in the connectors on the new latch assembly and postioned the latch back on the mounting holes. Replaced the stainless steel sheet metal and put the screws back.