MDB7760AWS0 Maytag Dishwasher - Instructions

removed rack
removed one screw
removed old seal
installed new seal
installed screw

I researched the internet about this symptom on the Kenmore Elite Dishwasher and I found lots of people with the same problem. Everyone fixed it by replacing the Bi-Metal Fuse. I removed the old fuse and tested continuity and it was indeed bad. Once the new fuse arrived I tested continuity and it of course worked as expected, so that was a nice wipe of the brow. The new Bi-Metal Fuse came with a nice instruction manual. I also used a video from YouTube to help with the repair as well, but the included instructions were enough. The only thing that was not clear was the best way to attach the new wire since it was quite a bit longer than what was orginially there. So I ended up just folding it up and putting everything back together and it worked just fine. This repair was very easy as long as you are OK with cutting and stripping wires in a somewhat confined space and not being too worried that you might mess it up for good... :)

replaced the valve

Remove the mounting screws that hold the dishwasher under the counter top. Remove dust cover plates at the bottom of the machine. The machine will have to be pulled out, so turn off the water to the machine. Usually under the kitchen sink. Disconnect water supply and push it out of the way so the dishwasher can be pulled out. Pull machine out enough so you have access to the door cables and springs. The door will have to be in the closed(up) position to do the repair. Usually only one side is broken. Start with the broken side and copy the working side when installing new parts. Then repair the working side. To get the working side apart just pull on the spring and disconnect it from the cable. Do the reverse to reinstall.

First of all I appreciate the instructions provided by this site when I selected the part I needed! The installation was so easy. I popped the end caps off of the top rack guides and removed the top rack. I reach in and popped the clips holding the top sprayer bar and gently pulled down on the sprayer bar enough to place the spinner button in the top of the sprayer bar. Then pressed the spinner on the bottom of the sprayer bar into the button I place in the top of the sprayer bar and reattached the sprayer bar to the clips. Put the top rack back on the guides and replaced the guide caps and it was finished. Easy fix thanks to this site great instructions!

Replacing the float switch was fairly easy and straight forward. removed old using adjustable wrench and replaced.

Replacing the door links was not difficult except I needed to pull the dishwasher out and had to disconnect the water line.
reconnecting the water line was the time consuming and frustrating part. Once that was hooked up and tested, i pushed the dishwasher back in place and all is good again.

Pulled dishwasher out from under the counter, removed faulty seal, installed new seal. Easy to understand directions are on web site.

I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.

Removed 2 screws that fasten dishwasher to underside of countertop. Pulled dishwasher out from under the countertop for access to sides. Hooked link on door, threaded cord around 2 wheels, hooked spring to back of dishwasher, stretched spring and hooked to eye on end of link cord. I found it very difficult to hook spring to link then try and stretch spring to hole at back of dishwasher. Easier to pull spring and link towards each other and connect. Note: This link was actually different from the original. The plastic end that connects to the door actually hits the first wheel when door is closed but it doesn't seem to prevent the door from locking properly (old design was better). However, I shaved this plastic end to provide better clearance.

Looked on you-tube and it was so easy. Pump on bottom right. unplug pump and do a halfway turn. Plug the new one up and place the pump on, and turn halfway and its on. START your dishwasher

I did not get to repair my dishwasher using the part supplied by Partselect.com. I pulled my dishwasher out and found that the connector had fallen of the capacitor during installation. Happy to say that I returned the part for a full refund minus the shipping. Have bought from them before, and will again

after all I read about the problems with Kitchenaid I figured it was the solenoid thats part of the soap dispenser. I took out all the screws on the door...2 long ones are on outer top...seperated it...took out all the screws on dispencer ring...replaced it...pluged it in and put the door back on. we ran it thru a cycle and the door now opens and makes lil soap bubbles.....another job well done by Hank in action! all the parts in door are easy to replace....

Replacement parts from factory installed using u tube support video


Also replaced stop ends for top rack by removing old clip in to push down and lined up to secure in slots at end of rack, notice new plastic parts are installed by pushing hardware into slots downward until they clip into place

Followed the easy how-to video from PS. It was as easy as changing a light bulb.

REMEMBER TO SHUT OFF POWER _ Had to remove the screws using TORX driver on the inside door edge-- then came the hard part -- the foam insulation is glued to the inner door and the outer cover- I was able to finally separate the cover leaving the foam on the inner door. Then had to break off the foam insulation on the lower third of the door up from the bottom. I then had access to the screws holding the air inlet to the door. The screws are located so you can't get a straight shot at them and it is very difficult to get at them. These screws are hex head metric and very small. When they are removed the old air inlet will come right off. Take the new one and duct tape it in place inside the door and replace the screws. I recommend doing the outer ones first and since they are the easiest to get started, then you can fight the others a little easier. After the screws are replaced and tightened replace the lower half of the insulating foam by duct taping it to the foam that remained on the inner door. Then replace the outer cover and secure with the TORX screws. This was a time consuming and tough repair. I don't recommend it to a novice.