MDB7749AWB0 Maytag Dishwasher - Instructions

Unplug dishwasher and slide it out from under cabinet. Remove old broken link (a heavy string between two plastic parts) and replace with new one. Slide dishwasher back and plug it in. Very easy and no tools required.

1. do not order or buy anything before examining the tension nut and washer. 2. Unplug the unit. 3. Open the switch box before trying to remove the float. Two types; easiest is pin based and lifts out easily. If the float catches, it likely has a headed bottom and needs an assist to lift past the stop flanges. 3. Using a standard ohmmeter, check for continuity. If it checks no need to replace. 4. Check float and assembly for abnormalities; cracks, lime deposits, etc. 5. Now decide what needs replacing. Did all my work with relative ease without pulling out the appliance. A couple sequences may need realigned.

I am a 61 year old woman and it took me a total of 2 min. max. Popped it into place and pushed in button that holds it..Taa Daa...perfect!

Pulled front panel and replaced door switch. Extremely easy but did not fix the problem.

I did not relize that the drain hose was in two parts. Naturally I ordered the wrong half. So after I relized my mistake, I re-ordered the correct part. Once the correct part was received the repair was easy and went well.

1) clear out the dishwasher
2) remove unit securing screws from top or sides of DW and cabinetry near the top or under the counter top
3) gently pull the dishwasher from the cabinetry about 20" is plenty, mind the connecting hoses and electrical connection
4) close the door! pull back the insulation from the area of the hinge and photograph both sides - this will save you the pain of going online
5) you will see the cord, the tensioning wheel assembly and the door balance spring on both sides
6) with the door closed to relieve tension on the cord, remove the cord from the balance spring - this can be done w/o tools at this point
7) remove the 5/16" screw from the plastic tensioning wheels and remove the tensioners, cord - leave the springs in place if not replacing them
8) install the door end of the cord to its hook on the hinge, install the new tensioning wheel assembly, install the old 5/16" self tapping screw through the lower wheel and into the outer hole in the frame
9) thread the cord from the door over the upper wheel and lower wheel. the lower wheel has cord retaining tabs to hold the cord on the assembly
10) hook the eye end of the cord to the balance spring and you are finished with the first side - repeat operations for the other side, reposition the insulation and slide the washer back in its cavity - do not forget to reinstall the stabilizing screws in the upper washer frame
11) you've done it!
12) have a cuppa and do your second washer that hasn't failed yet - it will soon.

The video included with this part is perfect. Unplug the dishwasher, take off the front trim piece, remove the drain hose from the pump, unclip the power, press the little clip that holds the pump in while turning it counter clockwise to remove. Then just do that in the opposite order to put the new one in. Just make sure you hear it click when you twist the new one on so you know the clip has engaged. Super easy.

put new hose on, very easy.

Just removed the old seal and followed the instructions that came with the new one. Since the old one didn't have any adhesive on it ,I didn't use the adhesice on the new one. Problem solved!

Remove 2 screws on lower baseplate. Remove 2 screws that hold dishwasher inside cabinet( may be attached to counter top or side cabinets). Turn off water supply to dishwasher. Remove any connections such as water supply, electrical connection, or waste water line that prevent dishwasher from being pulled out about 3/4 of the way. With the dishwasher door closed, remove broken parts and replace with new parts. Pull on spring to make final connection of nylon cable. Reverse the above instructions for re-installing the machine.

I opened yutube and noted the tips on how to fix specific problems with my dishwasher. That "steve" guy was very helpful. I tested the old bi-metal fuse with no flow and ordered a new replacement through partselect. The part arrived in one day and was fitted quickly. I used the teat meter to confirm that the fuse was ok before I installed it. The only problem that I had was identifying the part and number from a diagram which I did not have.

Turn off breaker to dishwasher.
Remove lower basket.
Drain any water using a wet vac.
Remove bottom cover plate. Should be 2 plastic screws using flat head screwdriver.
Should be able to reach pump. Turn counter clockwise to remove.
Disconnect plug wire on pump.
Install new pump by turning clock wise.
Reattach wire plug.
Run a wash cycle with empty dishwasher and check for leaks.
Replace cover plate.
Done.

Removed the old hose, after loosing metal looking rings. Installed new hose ad finally tight firmly the looking rings, using wrench and socket.

I followed an excellent video on youtube which shows how to do it step by step: Dishwasher Dispenser Assembly (part #WPW10605015) - How To Replace

Snapped the new stops on. It took about 2 minutes.