MDB7609AWS2 Maytag Dishwasher - Instructions

Pulled dishwasher out from under counter. Relaced cord with plastic hook attaching spring to door. Very easy.

Very impressed with Partselect.com. Full schematic of dishwasher made it easy to select part.

Delivered in 1 day. Fantastic. Highly recommend

First I unplugged the dishwasher.Then I removed 6 Torx screws, popped off cover, cut wires to old fuse, stripped wire, placed wires in new part, tightened screws, reassembled in reverse order, plugged unit back in and tested. WOO HOO!

I saved over $150.00 by doing it myself instead of having a repairman come out! That's 4 free fishing trips!

1. Removed six screws securing outer panel to dishwasher door.
2. Removed outer panel which exposed back of dispenser.
3. Remover six screws holding dispenser.
4. Removed dispenser.
5. Installed new dispenser.
6. Replaced six screws.
7. Reattached electrical connection to dispenser relay.
8. Reinstalled outer panel with six screws.

Started as dishes not getting clean and I observed that the top arm was not spinning and there was very low water pressure coming out of the jets. After making sure the water level was up to the bottom of the heating element and making sure the jets were not clogged I checked the filter and chopper. It was a little tough to get the cover off of the chopper but once I did I could see that the chopper scraper was broken off and the shaft was broken. The screen was all clogged up with stuff. Ordered a new assembly and put it in making sure to compress the spring and make sure the gears lined up. Now it is running great.
I think the Kitchenaid is the same as the Whirlpools.

I watched the instructional videos that showed how to replace the inlet fill hose/water inlet a couple of times. The repair was exactly as shown. No trouble at all.

After I took apart the inside of the door, removing 12 star screws, I was able to see the inside of the automatic soap dispenser device. Since I now had the new device to look at, I was able to replace the latch pin back in the existing device and it worked!

I now have a replacement if the device actually breaks in the future and looking at the small plastic pieces, it will probably happen sooner or later.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Removed the Bi-Metal fuse and ordered a new one and recerved it two days after ordering. Replaced it and it worked.

I ordered this part after the sanitized light on my dishwasher was flashing. The dishes were no longer drying. To replace the part, my husband pulled out the dishwasher and unscrewed some nuts (accessing under the heater through the side openings). The entire repair took under 15 minutes, and works perfectly. I have to mention that the heater was shaped differently than the one it replaced, but was a perfect fit in the clips.

Removed dishwasher from under the counter and took it to my shop. With the washer on its side, I removed the motor, then the impeller and seal. I then disassembled the motor and replaced the front bearing(purchased separately). This required an arbor press. I then reassembled the motor and installed the new seal and impeller. Reassembled in reverse order. Reinstalled under the counter and made conections. Checked for leaks and proper operation.

I cleaned the chopper and screen a few times and it continued to get blocked after a couple of cycles. Replaced the chopper assembly and now it works find.

Remove two screws at top that fasten dishwasher to cabinet. Slide dishwasher out to expose the two links that attach the door to the springs. Fit the new links to the springs and door.

First i remove upper rack held in by 2 clips at end of metal tracks. Compress inside clips and pull up then slide rack out of tracks.Then remove bottom rack just pick it up.Then i removed bottom sprayer by unscrewing center thumb screw. Then removed feeder tube for top sprayer held in place by 2 ea. phillips screws one on celin of tub and one at back of tub. Move tube to the right which unlocks it and remove. This has to be done to expose 4 ea. star screws. Remove screws and pop screen cover off. You have to take a towel and soak up water to expose bottom of inlets and outlets for water. You will then see the chopper blade with metal screen behind it. It is held in place with on star screw to the left of round top cover. Remove cover and pull on chopper blade which will release it from fingers mated from shaft to chopper blade .While pulling on chopper blade toward front of dishwasher pull up on metal screen it will come out. Clean all food particals out i used a shop vac worked well. Be careful not to drop screws in water inlets. The plastic shaft was broken in half by a piece of dental floss wrapped around shaft. I hope this helps it was not that diffacult just hard to work over door.

The first thing I did to repair my diswasher was call a repair company. They wanted $175.00 just to look at it, so I scheduled an appointment. Then, I did an internet search for dishwasher repair. I learned about bi-metal fuses, and how to check them. I found my bi-metal fuse was bad, so I ordered a new one through parts select. My part arrived in two days. I installed it easily, and the dishwasher worked. Finally, I canceled the repair appointment.

Take 10 lower star srews from inside of door (5 per/side) that hold on front. Remove front door panel. Remove 6 screws in detergent dispenser and replace.