MDB6702AWQ0 Maytag Dishwasher - Instructions

after reading a article on problems the logic one was frist the door. Order the part ,took off the inter panel with star slot (10)exposed the handle and switch. Removed it, abit hard at frist,then replacement went in easy , the washer worked.
I guess I was lucky because on the other side of handle similar type of part thats maytag for you.

The big problem is that you cannot purchase the wheels only. I found that out after ordering the rack track because that looked like what I needed. But it didn't come with the wheels. So I returned it. Then I went to the basement and found things in my junk boxes and fixed it without purchasing the complete parts. Cost: 10 cents for two nuts vs $60 for the required parts.

Difficulty was primarily because there were no instructions for the procedure so trial and error. I suggest: 1) Turn off power circut to the dishwasher. Then remove the star headed screws on the panel with door open and this separates the interior plastic door liner from the exterior door panel 2) remove the 4 screws inside the door that are the final fasteners for the exterior panel and the metal brace 3) bottom of the old door panel is curled and needs to be bent back slightly at the bottom 2 corners with a screw driver or pliers so the old panel can be removed by sliding the panel upward past corner brace while being careful with the electrical connections 4) once the old panel is removed the new one can be slid down the door arms and the interior screws attached 5) finally install the star head screws holding the interior panel and the new exterior panel. Restore electrical power and enjoy the new look of the ss panel.

took screws our of side trim and top trim, decreased height on leveler legs and pulled dishwasher from the cabinet, replaced cables and springs from both sides on the door, lubed door hinges cleaned everything under dishwasher re-inserted and re-installed trim screws. took around an hour with clean up.

The part broke off a while ago, and I did not want to call a repair person. The machine still ran, so I ran it with the part missing - the glasses were not very clean, but the repair call was expensive...

I figured that I had a snowballs chance of finding the part number on a molded plastic piece with no numbers printed on it. Boy was I wrong. I was able to choose the part off of a schematic of my machine right on the website and it linked me to the right part order form, so I did not even have to go back and find it on a list.

When the part came, all I had to do was unclip the old mount- with my fingers- no tools, and snap in the new part.

A for maytag for making it easy to fix
A+ for PartSelect for making it so darn easy

First I turned off the power at the fuse box. I then removed the 10 screws that hold the door tub panel in place. Then separated the door tub panel from the door. Removed the 3 screws for the black control box. I unplugged the flex cable that runs to the touch panel from the black control box. This is done by sliding the white rectangle clip that holds the flex cable. I then removed the 4 screws that hold the front touch panel, which I was replacing. Put on the new touch panel. Replaced the 4 screws. Plugged the flex cable back into the control box. Slid the white rectangle clip back in place to hold the flex cable. Replaced the screws on the control box. Put the door tub panel back in place and replaced the screws. Power turned on, all done and it worked.

Accumulator was as easy as just removing srews and replacing the part. The Float I broke by accident and was more complicated to replace required 2 people to manage parts.
Dishes finally coming out clean!

threw out the broken and put in a fantastically improved new one. very easy (would have done it sooner if I'd known it was that simple to find it online and order it) thanks

Open door fully. Remove all screws that hold inside panel to Front panel. Carefully remove Inside panel being VERY CAREFULL not to pull wiring out of door switch [top of door] and operator switch panel [also top of door]. Remove door switch, next remove 3 screws holding switch panel in place. Remove the top plastic section where switch panel mounts and set aside. Carefully remove green ground wire from bottem hinge for door. [right side] Next CAREFULLY remove front panel from hinges using EXTREME CARE not to let hinges "free fall" to the open position. Remove old panel. Install new panel in the reverse order as the old one was removed. DO NOT PANIC if you happen to pull the "ribbon cable' out of panel switch. It will plug back in very quickly and only one way. Just make sure it is "seated" in plug. The "key word" for this panel replacement is CAREFULLY.

Removed filter cover and filter and found the plastic chopper sleeve was stripped out. Followed instructions that came with the seal kit to replace it.

remove old seal, put in new - my 10 yr old could do it. Note - there is a white mark on the back of the seal indicating the middle so you can line it up when installing the new seal - makes it easier.

Basically took out of box and put in dishwasher.

I followed the directions in the dishwasher manual how to remove the top rack of the dishwasher, basically removing the stops on each side, and I set the rack on the counter. I replaced both sides even though one had not yet broken. To replace the part, 5 screws had to be removed; I used an allen wrench. The replacement location of the part was pretty obvious once the screws were removed. The inside of the plastic piece that was opened in the process of removing the defective part was dirty so I took some time to clean that out before attaching the new part. The actual unscrewing and attaching the new part probably took 10 or 15 minutes per side. It took a few tries to get the height adjusting lever to move freely before I tightened the screws. The rack works great now.

Took the dishwaher apart. Found out the float was damaged. Replaced the float and the float switch. Put back together

Snapped out the old retainer, snapped in the new. Then snapped in the washer arm. Done. Works great.