MDB6702AWW0 Maytag Dishwasher - Instructions

I removed the main plastic bolt with a pliers and then just used a screwgun with a star tip for all the screws.
I am a 43 year old woman with no experience and I was able to figure it out. The machine cleans much better now.

I removed the inside door panel, unplugged the old assembly and replaced with the new. The only caveat is that I THOUGHT the unit came WITH a new plastic handle, and it did not. It was very difficult to remove the handle from the old unit, and to install it in the new unit. The description was not adequate. I had read other blogs and they warned of the same missing handle, and I thought I had ordered correctly. The repair is fine, but the old handle is cracked, so I dont know how long it will last.

1. remove inside door panel
2. verified the part needed using partselect web site (entire latch assembly).
3. removed connecting wire sockets and replaced part and door (simple process).

First I made sure the breaker for the appliance was turned off!

I only had to unscrew all the screws from the inside door.

Next I used pliers to pry the old Latch Assembly (it is all pig tailed so only to plugs to undo).

Next, I snapped the new Latch Assembly into the two sockets.

Screws were replaced and wa la!

Turned breaker on and tested. Easy as pie. Took about 10 minutes from collecting the tools, fixing the problem, and replacing all the tools.

I actually had my 14 year old daughter do it so that she could learn how to make small repairs. This would have easily cost approximately $150 for a repairman to come and fix.

Then we went to the garage and unstuck the valve on the carberator to our '75 Chevy! (it was cold).

Not bad for a couple of girls!

Replaced with the new basket. However, the part had been replaced, and I do not like the new setup. One basket has been replace with 2 that are hooked together. Each basket has a cover, but it covers the whole side, not just a part. In my old basket, I had a part of the basket with a cover that could hold plastic lids and measuring spoons that can easily wash out of the basket and hit the heating element on the bottom. My "fix" was to remove both lids and use the lid from the old basket to cover one part of the new basket. It's not very satisfactory, as it is not hinged and had to be removed and tucked in each time!

Pulled out the old one and put in the new one!

No repair needed, just inserted the new dishrack. My only complaint is the lack of upright tongs in half of the rear section of the rack. This limits the number of dishes that can be stored. My original rack had tongs in all areas which better suited my needs. If there is a replacement that better suits my needs I would like an exchange.

The actual problem was the plastic wash arm cap was worn down and not holding the spray arm in place allowing it to hit the lower dish rack and stopping it from turning. The cap is on a threaded steel stem and is easily removed. The spray arm lifts off the stem and its replacement slips right on. Then install the new wash arm cap by screwing it on the stem.

1. Remove both upper and lower dish trays
2. Remove the “Spinner /Sprayer” (small nut on the top)
3. Unclip the “Tower” from the top and rear clip
4. Remove the “Tower” from the unit
5. Remove the “Filter Guard” on the bottom by removing 3 torx screws
6. Remove the “Discharge Housing” & “Impeller” (1 – 15 torx screw)
7. Remove and replace the “Accumulator Filter” (8 – 20 torx screws)
8. Assemble in reverse order

Shut off the electricity to the dishwasher. I removed all 11 screws from the door panel. After separating the 2 door panels, I removed the 2 door switches from the door handle ( I used a flat head screw driver to help get them out). Then I unplugged the 2 switches and plugged in the new ones. I replaced the door switches into the door handle ( this was not an exact fit because the new switches is slightly larger than the old ones). I put the new switches in place as tight as I could in the handle. I screwed the 2 screws holding the handle first to secure it before I put all the other screws in the door panel. I turned the electricity to the dishwasher back on. Our dishwasher has been working perfect ever since then and it is over 10 years old.

Took out the old basket,
Threw it away.
Popped in the new baskey,
filled it with forks and spoons.
Works great!

By the way, my order arrived in one day.
Phenomenal!

Remove screws holding the existing white panel. Once that panel was loose, there are several screws internally that have to be taken out in order to fully remove the panel. The new panel is then installed by putting it in place and reinserting the screws. It is an easy"fix" to change the DW to match other stainless steel appliances. You do need to be careful to make sure the door springs stay attached.

The door wouldn't close and it thought it the sensor was constantly open so it would turn on even if the door was wide open. Took the 10 or so torx screws off and removed the cover. Lifted the old assembly out and had to use pliers to get the wires detached from the door sensors. Attached the sensors to the new assembly, replaced the cover and screws and that was it. very easy fix.

Docking station just pops out, you grab the right side and pop it off. Replace by placing the left side in place and then push the right side until it snaps in place. VERY easy.

The gaskets were worn out and that was allowing a lot of water to escape, not enough pressure to clean the dishes.

Removed the rack from the dishwasher.
Took off the adjuster from the rack using the allen wrench.
Replaced the new.

Perfect