MDB6701AWB3 Maytag Dishwasher - Instructions

threw out the broken and put in a fantastically improved new one. very easy (would have done it sooner if I'd known it was that simple to find it online and order it) thanks

remove old seal, put in new - my 10 yr old could do it. Note - there is a white mark on the back of the seal indicating the middle so you can line it up when installing the new seal - makes it easier.

Snapped out the old retainer, snapped in the new. Then snapped in the washer arm. Done. Works great.

Replaced the door gasket, inner foam strip and the bottom seals on the door. Unfortunately I broke the plastic door latch handle in the process and had to purchase a complete latch assembly too.

Basically took out of box and put in dishwasher.

Door gasket fit in like a champ! No special tools required - just scissors to trim off the excess ends. Unfortunately this didn't correct the leak. The leak was caused by a Home Inspector who ran the dishwasher without soap. The soap has a defoamer in it. If you run the dishwasher without soap the water mixes with the surfactant in the jet dry and causes foam which results in a door leak. The foam also causes the pump to cavitate which is not healthy for the pump.

Removed the bottom tray. Removed the two clips in the top tray guides and removed the top tray. Removed the top spray arm and transfer tube by unclipping it from the top and at the back and then rotated it down and out. Removed the six screws around the upper pump housing and removed it along with the bottom spray arm. Removed the three screws holding the filter protector plate and removed it. Removed the two screws holding the accumulator / flow plate and removed it. Put it back together in reverse order careful to not over tighten the screws.

I removed the old door seal -- it just slips right out. Then I inserted the new door seal. One thing I noticed on the old door seal and also in your photograph is that the last inch or two of the seal on both ends is kind of sliced in half perhaps to make it fit better in the corner. But we decided not to cut it yet and have been using it uncut as it arrived in the package. It is working great! No leaking! So we're not going to cut it. Thank you for offering this great service. It saved us a lot of money since we didn't call a repairman.

Wanted to change our dishwasher to a stainless steel appearance. When the panel was delivered in 1 day I might add it was flawless. I removed the old panel and the new panel attached to the dishwasher perfectly with the screw holes exactly lining up. The most inexpensive way to turn a kitchen into a stainless steel appliance look.

Unfortunately, my experience was unlike that of the other people who posted. While everything did go back together it was very difficult to get it all to press down tightly enough to tighten each set of screws. The project took about 2.5 hrs and I still don't think it is exactly right. I'm still going to have a professional out to finish the job. Also, the tool needed to complete the job was nothing fancy, but also not in everyone's home tool kit.

from inside the door remove torx screws down each side and top , pull panel back , removed 6 screws from back of dispenser ,unplug 1 wire connection ,reverse procedure , real easy repair.

The repair was much simpler than I had anticipated. I just started removing screws, remembering what screws went where, and carefully removed the parts I needed to until I could get to and remove the filter unit. Installing the new unit was a snap, then it was just a matter of putting everything back together.

I remove the inner door panel, disconnected two quick release connectors, unscrewed the old part from the inner panel and installed the new one.

The new part arrived quickly and was the perfect match.

First I watched the repair video provided at your site. Once I got the right part, it went like a breeze. Just a phillips head screw driver and 5 minutes of my time. Speaking if the right part.... I would suggest that you remove the 'LATCH-DOOR-NO Handle' from your parts list.It only cause confusion in ordering the part I needed, and a loss of several days time in the repair cycle.
All in all, a good repair experience. I would reccommend you to my " Do It Yourself" friends.
Thanks,
Harold L.

1.Disconnected the electricty 2. pulled the dishwasher from under the cabinet 3. tilted the washer on it's face (water supply was long enough and did not need to disconnected.)4. unscrerwed the 2 plastic nuts that hold the heating eliment in place. 5. tilted the dishwasher back upright and removed the old heating element. 6.put the new part in place had a helper tilt the washer forward while i tightened up the two plastic nuts to hold the part in place.7 reattached the elecrtic conectors to the heating element. 8. pushed the dishwasher back in place. 9 hook the electricity back up. During step 4 i had to remove the electric connectors from the old heating element.