MDB4651AWB2 Maytag Dishwasher - Instructions

Pulled out the old one and put in the new one!

Replaced with the new basket. However, the part had been replaced, and I do not like the new setup. One basket has been replace with 2 that are hooked together. Each basket has a cover, but it covers the whole side, not just a part. In my old basket, I had a part of the basket with a cover that could hold plastic lids and measuring spoons that can easily wash out of the basket and hit the heating element on the bottom. My "fix" was to remove both lids and use the lid from the old basket to cover one part of the new basket. It's not very satisfactory, as it is not hinged and had to be removed and tucked in each time!

I watched a couple of videos on Youtube, and for once it was actually easier than anticipated. Unplug unit. Remove door screws. Separate inner door from outer door. Remove connector from dispenser (needed flat blade screwdriver to pry it at first.) Remove six screws holder dispenser in. Removed old dispenser, inserted new one, tightened six screws, re-connected wires, attached inner door to outer door, and was done in literally less than 10 minutes. Note: I was using a battery powered screw driver to remove the screws, so that's one reason why it went so fast.

Ordered part. (Part was larger than the original . That is it dis not fir int supports tha same as rhe original. Hut i modifird the support by assin copper wire to fanten the heater to the supports.) The instalation was no pronlem with a little engineering. Works like a charm, Wife Happy Most important result.
Elmer

Removed two screws at the top of the base washer. Three screws removed down both sides of the base washer. Lifted washer out enough to see the cable and spring connections. Removed cable and replaced with new and re-connected. Slid washer back into position and installed screws.

1. remove inside door panel
2. verified the part needed using partselect web site (entire latch assembly).
3. removed connecting wire sockets and replaced part and door (simple process).

Basket Replacement very simple just remove old and set new basket in place

Pull dishwasher about 1/2 out of cabinet. Remembered to turn off power just in time. Removed electrical leads. Hand removed nuts retaining the heating element. Installed new element - hand tightened nuts.

Remove screws holding the inside of the door. Set lid aside. Pull out the old foam insulation. Clean the area. Replace with new foam insulation. Put door back together.

Took out the old basket,
Threw it away.
Popped in the new baskey,
filled it with forks and spoons.
Works great!

By the way, my order arrived in one day.
Phenomenal!

The old docking station seals were getting very soft. To put a band aid on the wound until the new docking station got here I put a sleve on the washer bar feeder tube. This made an improvement. The docking station was removed using a screw driver to unsnap the station. Then all I had to do was snap the new one in. Be care ful not to pull on the piece the docking station is snapped on to. There are metal clips behind there that hold that water delivery tube on to the back of the dishwasher. Those clips are twisted on and can be striped off easily by pulling strait towards you. If that happens you must secure the clips using self tapping screws and a water proof sealent.

Docking station just pops out, you grab the right side and pop it off. Replace by placing the left side in place and then push the right side until it snaps in place. VERY easy.

The gaskets were worn out and that was allowing a lot of water to escape, not enough pressure to clean the dishes.

The door wouldn't close and it thought it the sensor was constantly open so it would turn on even if the door was wide open. Took the 10 or so torx screws off and removed the cover. Lifted the old assembly out and had to use pliers to get the wires detached from the door sensors. Attached the sensors to the new assembly, replaced the cover and screws and that was it. very easy fix.

Not much to report on this repair. I removed and discarded the old rinse aid knob, and replaced it with a new one.

Removed the rack from the dishwasher.
Took off the adjuster from the rack using the allen wrench.
Replaced the new.

Perfect