MDB4709AWB1 Maytag Dishwasher - Instructions

Ordered a new pump (after a online diagnosis). Followed the instruction video on the website...also took the time to replace the discharge hose due to residue buildup...tested dishwasher (one cycle). Slide dishwasher back into opening....DONE. Works perfectly. THANKS

Pulled washer out far enough to put 2x4’s under front feet. Removed front panel, I clipped wire connector and unplugged it. Pushed plastic locking lever in and twisted unit counterclockwise. Wiped inner rim and reversed above procedure to assemble.

Take out 6 screws from inside door upper most screws to control panel, removed water safety shield 3 easy tabs to release, found old fuse removed , cut wire 1 inch from old fuse removed have to pull fuse out of its plastic holder put in new fuse matched up wires, they are color coordinated, black with white stripe, and one solid black striped wires and twisted them tight, and inserted them in new wire harness that came from parts select tighten them tide them all together and used black electrical tape on all the new connections put back together and it totally fixed the problem so happy saved alot of money not having to call a service repairman

I closed the water at the tank and opened all the hot water faucets in the house thereby draining static water from the inlet hose at the valve. Then I unscrewed the inlet hose from the valve, unscrewed the valve body from the support bracket under the tub, unplugged the electrical plug from the valve body, and removed the outlet hose. I installed the new valve using the reverse sequence. Then I closed all the hot water faucets, turned on the hot water at the tank, and purged air from each of the faucets. I then started the dishwasher and ran it through a complete cycle, periodically checking it for leaks, and found none. Total time for uninstall and reinstall - about 30 minutes. Not bad for an 80 year old.

The repair was straightforward. The hardest parts were pulling the dishwasher out from the counter and keeping the dishwasher from falling forward when I needed to reach inside. The instructions in the video were accurate. I was very glad I bought the rubber washers, because I could not reuse the washers from the original heating element. Easy enough repair to do on your own.

Used bowls in upright position in upper shelf determining no water to upper shelf after running in rinse cycle. Added a cup of Vinegar in rinse cycle. Performed bowl test in upper rack & still no water in bowls. Dismantled inside of unit by removing both spray arms & found lower seal deteriorated & upper seal in need of replacing. Replaced seals & redid bowl test & found no water getting to top rack still. Found utube vid showing removing garbage disposal portion of unit. Requires removing screen in bottom of dishwasher. One screw attaches garbage disposal cover. Found non food items & food by broken garbage disposal. Repaired disposal, removed debri & reinstalled all components. Redid bowl test in upper shelf & bowls were overflowing!!????Dishwasher works GREAT now & can hear garbage disposal operating along with massive water being sprayed!!!

Very simple just remove the rakes and then unscrew the covers and pop out the old chopper assembly and replace with the new and then just put all cover back and it works great.

At first, I figured the noise was coming from underneath, and took off the bottom front plate. I noticed there was a leak from the center of what I later learned was the "pump" assembly. So I unplugged the dishwasher, disconnected the water and drain from under the sink, unscrewed the screws holding it under the counter, and pulled it out from under the cabinet. Then I laid it on its back, and realized where the leak was coming from. At this point, I thought the noise had been coming from the motor. So I detached the motor (required use of a socket, and realized it was "free", so thought the problem must be further up inside. Reached my fingers in where the motor mounts and found part of the chopper assembly. The "chopper" had torn itself free from the screen. Realized at that moment I needed to disassemble the pump from the top. Took off water distribution system, bottom water rotor, pump plate (required use of "star" screwdrivers, two different sizes), foreign object plate, and chopper assembly cover. Getting the chopper assembly cover off was hard; had to pry it with sharp l-shaped poker; it was adhered with calcium deposits. Finally got it off, found rest of chopper assembly (screen with hole in the middle where chopper had been), ordered chopper from PartSelect, took 3 days, installation was easy, the reverse of removing it. (It is not necessary to remove motor to replace chopper assembly.) However, it is still leaking from the bottom, and I'm at a loss as to how to fix that.

Long story short, noticed one of two leaks and came to conclusion there is no workaround since sump pump gasket seems to be hermetically sealed to sump pump. Which is understandable because of water in area. Wife helped by soaking other parts that were removed and replaced, because of calcium buildup. Which we hope will extend life of dishwasher. I put 1 to 2 hours because I took my time and made sure all parts fit correctly and were back in their original place. Didn't want to take any chances in not covering bases. I am no expert, but definitely a diy'er. I believed I saved myself anywhere from $200 to $300 in labor costs by repairman. By the way, thanks Parts Select your info and site are awesome!!! The second part I had to order was the water inlet valve and your phone representative was a big help over the phone, please don't eliminate those positions. Overall total price of parts approximately $130 w/delivery. Well worth it, since a brand new halfway decent dishwasher starts at $550.

The repair was very straightforward. I followed the excellent video provided by Part Select and the repair went exactly as shown in the video.

The only minor challenge was removing the dish washer from the cabinet, and disconnecting the utilities (electrical, water, drain), as these elements of the repair were not covered by the video. Fortunately Part Select included a copy of the installation instructions that come with this dishwasher; those instructions gave me the information that i needed to "uninstall" and "reinstall" the dishwasher as part of the repair.

It was ok but screw holes were not in the right spot but we put one in and that is sufficient for now. It prevent thing from follow under it.

Unplug (disconnect power)
Shut off water
Disconnect water supply line
Clean up any water spills
Remove clips holding air gap hose and wire inside cabinet.
Open dishwasher door and remove two screws that secure dishwasher to cabinet (these are at top of door opening).
With door closed, remove panel under door (this has a screw clamp on each side that requires a quarter turn to release).
Lower the dishwasher as necessary to provide vertical clearance by adjusting leveling legs.
Pull dishwasher out from under counter (grip from under door) far enough to expose springs (one on each side). Take care to feed all connecting lines smoothly through cabinet opening.
Note how existing springs are installed.
Install new spring in the same fashion as the old spring was installed.
Test the door operation.

Push unit back under counter taking care to draw connecting lines back through cabinet opening.
Readjust leveling legs as needed.
Reattach unit to counter top.
Reattach water supply and open valve.
Check for water leaks both at valve and under unit, fix as necessary.
Replace panel under door.
Replace any clips inside cabinet.
Reconnect power

Couldn't do the repair because you people sent the wrong part.
I ordered #1174536, spray arm seal, but got #wp8268340, bearing.
Waiting for you to make this right.
Please feel free to publish this. Tom Hanna

It is a small plastic piece which serves as a stop on the right side of the upper rack. It is the correct part because it is identical to the left one of the same type. I tried clamping down with a pair of pliers but I am afraid of breaking it. With shipping this two inch piece of plastic cost $20, so I do not want to crack it. I am at a loss as to how to sit in in place.

Repair not completed due to wrong part received because an image of the part needed was not posted on website. I could only trust the one-word description, “wheel”, was describing the part I ordered. It was not.