MDB4630AWB5 Maytag Dishwasher - Instructions

Fast,smooth,easy.

Just click in, you can basically do it with your eyes closed

Just pulled the old gasket off and started on the bottom of both sides of the door installing the new gasket and finished at the top in the middle.

Recently bought a whirlpool dishwasher, the dishwasher was converted to a portable dishwasher and they did not use the cord application power cord so they machine was blowing our breaker, instructions were very simple and installation was easy!

removed old door gasket, cleaned gasket groove, and than started new gasket in both corners working my way to middle top of door, made sure gasket was in groove properly w/my fingers. problem solved

Removed bottom sprayer by turning thumbscrew clockwise approximately 2 turns. Disconnected pipe that feeds upper sprayer by twisting approx. 1/4 turn in CW direction. Removed 4 screws that hold the bottom plastic plate. Removed 2 screws that hold plate on bottom of unit that also holds the choper assembly cover down. Pried off chopper assembly cover and removed broken chopper assembly and replaced with new. Reassembled all parts in reverse over described above.

Disconnect power Pull out dishwasher. Turn it 45 degrees to your right. Turn it on its side. disconnect the connections to the heating element {2}. Remove bolts, remove element. Install new element and tighten bolts. Reconnect electrical connectors. puch it back in place. reconnectPower your done

If your are just a tiny bit "handy", you can do this job in about 30 minutes for $30. The rubber gasket comes off very easily from its location, just pull it off, than, using a small piece of wood, I used a shim, insert the new gasket in, an inch at the time, all around the frame. No more leak, and probably over $150 savings. A plumber or repair man would have charged $90 just to drive to my house, plus part & labor.
Thanks to PartSelect too, the part was delivered rapidly and the all ordering process was painless.

The replacement os the part is very easy if you know how to disconnect the pipes for the upper deck (for my model, you take the pipe out of the clip on the back wall and swing to the right about 30 degrees). You need 2 different size star screwdrivers to remove the rest of the assembly, 6 screws in all. The choopper assembly is easy to remove and replace. Just make sure you pull the spring loaded blade back so it can fit into its maid. Reconnecting the pipes back up can be tricky. Make sure the pip is connected at the 30 degree angle, then bring into it's normal position.

Was a simple task to perform, a child could have done it. The technical skills diagnosing it was a bit hard though. The skills finding the culprit was indeed simple. Rubber was torn. Dishes would not come clean especially on the top & would not dry properly. The rubber piece being torn in half made it hard for the water & soap to despense to the top through thh center plastic tube, but now it cleans great. Thank's
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.

After disassembling the entire motor assembly, I discovered the chopper assembly was broken. This could have been accessed from the top. in any event, I found the problem and fixed it with a new part. After re-assembling the unit there was a small leak coming form the edge of the motor assembly this was resolved by removing the gasket and smoothing out the contact surfaces that were damaged by the removal of the motor assembly.

laid dishwasher on its side and unscrewed element. returned unit upright & replaced element. reversed process and reinstalled unit under cabinet

Watched a video and seen how easy it was to repair. Just disconnect the power, water and return drain. two bolts and replace element . The difficult part was removing and replacing the dishwasher...piece of cake.

removed the upper and lower baskets, removed the lower wash arm by rotating the center bearing assembly (its the flat piece in the very center of the lower wash arm) by the way it has a reverse thread...not righty tighty and lefty loosey... it is reverse the normal rotation.. i unlocked the upper arm assembly from it's clip on to mount as well as the clip on to mount on the back wall, looking at the very center pump cover strainer, you will see that the assembly that goes from the pump area to the very top of the machine needs to be rotated clock wise where it locks into the pump strainer assembly. now remove the four star type screws from the face of the strainer, now you can lift out the entire bottom of the machine you will see the half round cover in the bottom of the well, remove one smaller size star screw. simply remove the chopper assembly and install the new assembly as indicated in the instructions provided, be sure to use the trick with the open end wrench as per instruction sheet, makes it easy. now follow the bread crumbs you left on the yellow brick road to reassemble.

tom boy single Mom- not too difficult! Follow the video and installation procedures. My only problem was lining up the chopper blade, with the need to install on an angle and connect copper assembly with the motor, and align with groove, needle nose pliers did not work for me, due to the fact, pliers seemed to angle the chopper assembly and did not received equal pressure between the blade and the screen.( I did not have a collection of needle nose pliers to chose from) I used a fork to give even pressure distribution and keep the assembly even and it slipped right into position, remembering to line up all connections between the motor and the chopper assembly, the fork give me the ability to angle the assembly. Its like having a new dishwasher, I use the light setting now when washing a load. Saved $$$$$$$ and X-mas is on the way!!! Thanks Parts Direct!!! Will re-order when the next appliance repair occurs.