MDB4630AWS0 Maytag Dishwasher - Instructions

Followed included instructions... worked like a charm!

Follow the u tube instruction. Replacing the pump was very simple and easy. The hard part was getting the dishwasher out of the cabinet and back in again.

Disconnected the damaged hose extension from the dishwasher outlet drain hose and the connection to the sink drain. Removed two clamps. One a spring clamp and the other a screw clamps. Connected the new extension hose with a spring clamp to the dishwasher outlet drain hose. Connected the other end to the sink drain with a screw clamp. Checked for leaks. Good to go!

Only one friction sleeve was broken. So I pulled out the dishwasher to see how the one on the other side went on. It was very easy to replace and I replaced both. Unit works fine now.

really easy to repair... no power to control panel but had power from breaker box. Followed directions that came with part, self explanatory, took 10 mins.

quick and easy replacement, without tools...

i ordered the wrong part and received the new part and credit for the old part, quickly...Plus, I was kept informed with e-mails....

excellent service...

I spent more time reading the easy instructions several times than it took me to actually do the repair to replace the fuse. I wanted to make sure I fully understood the instructions before I undertook the task. I also checked out a video on You-tube which explained and showed me the same thing as the instructions did. By the time I picked up the screwdriver, I was practically "an expert". I just cut two wires and hooked up two new wires and... done. The instructions were simple....so was the repair. Nothing to it.

Repair was a "no brainer". Pulled out the old gasket, started the replacement of the new gasket in the lower right hand corner and worked all the way around the opening, then trimmed excess gasket of about 2" with a pair of scissors and I was done. Total time - less than 5 minutes.

I opened the dishwasher door, removed the old tired seal in a manner of seconds. I measured the old seal against the new, same length, so no cutting. I started on one side pushing the seal in to the groove, made sure the seal was centered in the door. (not too long on one side or the other) It took less than 5 minutes to place the seal and check that it was all the way in, all around the door. I wiped the door down with some cleaner, where it contacts the seal. The door was harder to close, but I expected that until it breaks in. I ran a short load in the dishwasher with no leaks. :)

Removed DW following great instructions for our unit at: repairclinic.
Problem when removing actual pump as a thin metal screen fell out after. Cleaned it and tried to reinstall the screen. It took over an hour figuring out how the screen went back in as it was cut to fit a certain way and had to try it over and over blindly then try to get it to stay before putting in pump. Finally put DW on its face. It was almost two hours after starting that everything was done exactly as instructed.

Started washer. Water came in perfectly. After about two minutes when the washer arms would start there was a horrible grinding sound and we promptly turned it off. My wife gave up the fight and is washing dishes by hand. That was a $172.00 experience.

Thanks to everyone for posting their experiences on changing the heater element. The most difficult part of the repair was getting the dishwasher out of the cabinet. I didn't know that I should disconnect the water line underneath the sink and this would make the removal easier. Also, because the copper water line going to the dishwasher was kinked, I ended up changing it with a flexible steel braided line.....much easier to install.

Once the dishwasher was out of the cabinet, I turned it over and easily removed the clips that held the heater element in.

I would definetly recommend people doing this repair themselves, it will save you a lot of money!!!!!

I had to remove the baskets, spray assemblies (no tools needed) and disassemble the section of the pump that contained the chopper assembly. (removing three Torx screws)
I had to remove a part of the old chopper that had gone into the pump, but I was lucky that a magnet grabbed it so I didn't have to disassemble the pump.
The total repair was not difficult. The only problem was access (hands in the way while repairing difficult to see) and compressing the spring on the new chopper while trying to slip it into the groove.
The parts came in three days and they fit perfectly

Repair man said I needed a new pump and would cost $350 to repair. This dishwasher was only 5 years old and we only use about once a week so didn't think the pump was gone. Went on this website and read some stories. this model has a mini garbage disposal with a chopper and screen which gets clogged up and prevents water from circulating. You can clean the screen without removing the dishwasher. Remove the cover plates on the bottom with 4 screws and the smaller cover plate underneath. Remove screen, clean and replace. If the chopper is broken you can order a replacement for $21. There is another story on this site with a lot more detail so I wont repeat here.

I closed the water at the tank and opened all the hot water faucets in the house thereby draining static water from the inlet hose at the valve. Then I unscrewed the inlet hose from the valve, unscrewed the valve body from the support bracket under the tub, unplugged the electrical plug from the valve body, and removed the outlet hose. I installed the new valve using the reverse sequence. Then I closed all the hot water faucets, turned on the hot water at the tank, and purged air from each of the faucets. I then started the dishwasher and ran it through a complete cycle, periodically checking it for leaks, and found none. Total time for uninstall and reinstall - about 30 minutes. Not bad for an 80 year old.

The repair was straightforward. The hardest parts were pulling the dishwasher out from the counter and keeping the dishwasher from falling forward when I needed to reach inside. The instructions in the video were accurate. I was very glad I bought the rubber washers, because I could not reuse the washers from the original heating element. Easy enough repair to do on your own.