DWU6750AAM Maytag Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- jerry from wilton, CT
- Parts Used:
- WP902894
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Door leaked from lower right corner
First I replaced the soap door grommet -- door still leaked. Then I went for the really expensive part ($40) -- the door gasket. The old one came right out and the new one went right in -- 15 minutes tops -- and the door no longer leaked.
Thanks to all the previous posters for their hints.
Thanks to all the previous posters for their hints.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brad from York, ME
- Parts Used:
- WP902899
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dispenser door would not open
Attempted repair was quick & simple. Removed 7 torx screws, and then pulled the wax motor out of its holder. Pulled 2 wires off, and replaced old motor with new motor. Reattached wires, & reassembled.
Only problem was this did not fix the problem, so back to square one, but worth a shot.
Only problem was this did not fix the problem, so back to square one, but worth a shot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carrie from Platteville, CO
- Parts Used:
- 902882
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
our dishwasher needed a motor shaft seal
I recieved a different part than was in the picture and description that I ordered, and was billed twice for it. I wasn't able to fix my dishwasher
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from West Union, OH
- Parts Used:
- 903096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dishwater cold
I removed lower cover panel. Removed two wires. (one on each end of the element. Removed two nuts on the element. Took out old part. Put new part in and reversed procedure. Works fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- serafino from oakland, MI
- Parts Used:
- 99002254
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dishwasher would not turn on
Once I removed the inside panel from the door replacing the switch was pretty simple. completed the job in less than twenty minutes.
This was the third appliance I have repaired with the help of Parts Select in the last three months.
This was the third appliance I have repaired with the help of Parts Select in the last three months.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Beaver Dam, WI
- Parts Used:
- WP99001791
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Wouldn't come clean.
New pump housing filter was needed as the old one was plugged and distorted.
I
I
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernest from Santa Ana, CA
- Parts Used:
- WP99001553
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Soapy water leaking from bottom of dishwasher door
The dishwasher was running perfectly, but over time it leaked more and more. We were ready to throw it out, when I searched the internet and saw stories about a tiny gasket commonly failing. I couldn't believe that could be the trouble, but ordered the $3.75 part. Unscrewed the door, slipped out the old gasket and slipped on the new one. Screwed the door back. And the result? THE LEAK IS FIXED! Unbelievable. The old gasket had gotten stiff, probably exposure to soap, and it wasn't sealing properly. That $3.75 part saved us hundreds and hundreds of dollars and will give us extra years of use from our dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from DELAWARE, OH
- Parts Used:
- WP6-918873
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
old silverware basket broke
Basket Replacement very simple just remove old and set new basket in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond G. from Whittier, CA
- Parts Used:
- 99002254
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dishwasher wouldn't start, no power on any setting
Removed door interior, confirmed with tester that power was reaching door cut-off switch, but not power on other side of switch when engaged. Noticed that little switch button frozen in shut position, assumed switch had burned out. Installer new door cut-off switch with new (dual) switch units in place, plugged in unit and it ran perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ellen from Woodland Hills, CA
- Parts Used:
- WPY912709
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Two clips holding the adjustable shelf had broken off.
I didn't know how to put in the new one clips until I looked up a picture of them in place, on-line. Once I saw the picture, it was a matter of clipping the new ones in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stacy from DEPEW, NY
- Parts Used:
- 99002254
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dishwasher would not start/run
Followed the instruction video provided by this site ! 15 minute repair?..Super Simple!!! I Love this company!!! Saved me a bunc of money!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from Tulsa, OK
- Parts Used:
- 99002254
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Unit would only stay on if one was pushing the door
First I removed power to the dishwasher. The inside panel of the dishwasher door is held on with several screws with Phillips heads. Remove those and the panel comes off. There is a silver metal guard that you have to pull off being careful not to tear the insulation that is on the other side. Then there is one hex head screw to take off the handle latch assembly. You remove this assembly and take off the wires to the two switches on each side of the assembly. The replacement part doesn't come with the black plunger that pushes on the switch buttons so you have to remove it from the old assembly. This was the only difficult part, I essentially destroyed the old plastic assembly getting it out. But putting it in the new assembly was easy. Then I attached the wires to the switches in the new part and reassembled everything. Works like a charm now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernice from New Vernon, NJ
- Parts Used:
- WP902894
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Leaks onto floor from lower section
First I replaced the door gasket as every one else. This cut drips about 30%. I then discoverd that the Rinse Aid circular dispenser cap was opened about half way. I turned the cap tightly clockwise to close and cut drips to 90% total. I czn live with the other 10%,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Ridgefield, CT
- Parts Used:
- WP902894
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lower left corner of the door was leaking every so often.
I first made sure the new gasket was long enough and it matched the original. Next I used the tip of a screwdriver to pick out a corner of the old gasket and then pulled the entire thing out. I noticed the old one stopped at the bottom of the gasket well. The new one was much longer and I thought I might have to cut it to length. Well I'm glad I didn't. If you start on the right side and work your way up and around with a 2 in. piece longer then what the old one was. I carefully tucked it in the bottom and closed the door. Glad I didn't cut the new one. Instructions would have been nice. Overall an easy fix. I'm very mechanically inclined so I knew better.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marc from GLENDALE, NY
- Parts Used:
- WP99002560
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
After 22 years of virtually trouble -free service, I could tell by the sound that something was wrong. Water fill ran too long. Float not stuck. Checked and found float switch stuck.
Very simple. Remove bottom panels. Remove one screw holding old switch in place. Move wire connections from old switch to new one. Cleaned and lubed the switch actuator. Mounted new switch. Checked that float and actuator worked freely. Left bottom panels off till I ran a load - just to be sure all was OK. Remount bottom panels...Done! P.S. Don't forget to turn power off to dishwasher any time you work on it!!
Was this instruction helpful to you?
Thank you for voting!