DWC7602AAE Maytag Dishwasher - Instructions

Took old one off , installed new one!!

I only really needed the lip seal that fits in the faucet adapter. After much research I discovered that the seal was simply not available. I tried to substitute a standard O-ring of the correct size, but it was too thick and did not allow the adapter to snap on to the faucet.

I purchased the complete hose assembly from Partselect.com, and received it quickly. I used a small screwdriver to remove the seal from the new hose assembly, and installed it in my existing hose assembly. The seal was a perfect match with the old one, it fit perfectly, and no more leaks.

Be careful not to damage the new seal when you are removing it. Also, be advised that if you choose to replace the entire hose assembly that you may need to replace the areator on your faucet, in this case the new hose would not fit on the existing areator, but fortunately the seal was a perfect match.

I removed the old door gasket and thoroughly cleaned the track. I placed the new door gasket in place- no problems.
I had to remove the 7 screws from around the door to access the old, crumbled gasket. This was accessed by removing 2 screws with a socket wrench. The old gasket pulled out and the new one slipped right in.
No more leaks!

I followed instructions of others that were posted. Door seal was simply removing old seal, cleaning track and pushing new seal in,making sure it was even all around. Removing the door cover to get at the Dispenser grommet was simply removing all 7 hex nut screws. Had to go out and buy the proper hex nut screwdriver . I did not remove the wiring, just turned cover over to remove the two nuts holding the dispenser. The nut on the left was a little hard to get off, had to kind of force the socket onto the nut. Otherwise all went well and simply removed the old grommet and installed new one. Finding the right tools was the part that took the longest. I had hard water before putting in a water softener so that was probably hard on the seals plus the machine was an older model. No problems now and saved having someone come in and do a repair.

My handy husband was able to take it apart easy, and then your online site was great at showing us exactly which parts were needed to replace. Then a few mintues to put the 4 pieces together and now I've got all the room I need for the extra dishes!!The whole experience was so easy and very helpful!! thank-you very much!!

Unscrewed the inside door panel. Removed the reservoir assembly. Disconnected the wax motor. Replaced it with the new motor. Replaced the new o-ring. Done. The hardest part was finding out why it was not working and how to fix it. Google for a long time in order to find some idea what to do. Then took the door apart to see the reservoir and the wax motor. After that, it was pretty easy. HTH

Attaching the part to the door only took a few minutes but getting the dishwasher out over the hardwood floor that was installed after the appliance was put in was a pain. I had to remove a piece of the hardwood floor and use some technique to get it out of the opening so that the springs were visable. There is no problem after that. I would recommend using work gloves to stretch the spring over the retaining notch on the door so that you don't pinch your hand.

I first removed the bottom access panel and 2 upper screws holding the dishwasher to the counter. Be sure to remove the standing water in the bottom tray. I pulled the chassis far enough forward to reach where the top shower hose attaches ( the supply line and wire had enough slack to move the chassis ). Not knowing how the rotating shower arm attached, I unscrewed the ribbed retaining ring above it, and found the whole assembly came loose - freeing the upper end of the shower hose. Put a shallow tray under the lower end of the shower hose to catch the remaining water and loosen the hose clamp to free the remaining end of the hose. Transfer the rubber washer at the top end and the hose clamp at the bottom, to the new hose and install. A quick repair, but one that shouldn't be needed on a 4 year old dishwasher.

I opened the dishwasher door, then used the Torx bit to remove the screws all around the edges of the door, and removed the inner part of the door. Then I removed the long metal plate at the part of the door farthest front (with the door open) and the large black plastic housing. The metal plate then became a useful tool to brace at an angle between the door and the body of the dishwasher. This not only held the spring-loaded door down, it also held the inner part of the door up against the body of the dishwasher.
One nut held the latch assembly to the door; I removed it with the nut driver.
On the latch assembly, there are two small plastic catches that keep the latch from sliding out, I held those out of the way with a blade screwdriver and slid the latch out.
The new latch then snapped into place, and I assembled the door again in the reverse sequence of disassembly.

I turned the dishwasher onto it's back. Using pliers, I grabbed right behind the remnants of the broken wheel and gently pried it out (took about 5 seconds). It popped out. I put the new white sleeve and then the caster wheel into the now open hole, slowly set the dishwasher back up and let it drop the last 2 inches. That pushed the wheel securely up into the sleeve. The entire replacement took less than 2 minutes! Super easy.

Although the (top) dishrack assembly included the nylon wheeles, it was easier to replace the old one by disengaging it from its wheels and installing the new rack on the old wheels kept in the slider track. The snap hook that held each wheel to the old rack was popped loose (finger pressure) and the old rack removed. The new rack was held in place and each of the four wheels snapped to it. Each wheel fits into a wire post on the basket and the plastic hook snaps onto the wire frame. The most difficult part of the 'repair' was removal of the handle from the old silver ware basket. I used screwdrivers to simultaneously pry the four tabs of the halde out of the slots on the basket and pulled (hard!) the handle off. It snapped easily into place on the new basket.

I have a new faucet so I remove the screen then I used an extender ring put on your adapter an got the washer to run.

The problem was the rubber end on the upper shower head pipe at the pump. Not to hard . Slide dishwaser half way ouy the ptpe is on the right side.The bottom end is is just a clamp the top drops in from the top, inside there is a nut above the upper shower head. You can unsrew the nut with your fingers, it is right above the upper shower head.There it a washer at the top of the pipe that should be replaced that doesnot come with the pipe

first I turned off the water to the dishwasher, and turned the power off for the dishwasher.
removed the 4 screws from bottom panel
then removed the 2 screws from the bottom of the counter,
at this point I could pull the dishwasher out. then figured out where the part went and attached.
pushed the dishwasher back and lined up the holes under the counter, put those in first, the put the bottom panel back on, turned the water back on, and flipped the breaker switch.
Reading the other stories really did help me get some idea of what needed to be done

The repair was very easy. The door gasket was a little short, but I gently streched it to the proper length. I replaced the other parts as a precaution as some others said they were really the source of the original leak. It went very smoothy and NO MORE LEAKS.