MDB8951AWB Maytag Dishwasher - Instructions

Ordered a new basket. Tossed out the old one. Done

I'm telling this story for my husband who is a pretty handy guy--I watched him do the repair. I had had someone out to look at the dishwasher and they said it would be $284 to fix this one little thing because you couldn't buy the one little part separately, you had to buy a whole new motor. Since the dishwasher is old, it didn't make sense to invest this much in it--might as well buy a new one for that kind of money. My husband did some looking around and found the part on your site and installed it himself. So the cost was under $40. The dishwasher is now working better than it had been for a while.

First I removed the screws from the inside of the door exposing the latch assembly. Removed the old part and installed the new assembly. Don't screw it on to the door untill the cover is on again.
First I ordered only the latch without the handle. Found after opening it up the handle was broken on the inside so had to order the assembly. It's a piece of cake to install. If you're having touble opening the door don't think because the handle looks ok from the outside it's not broken.. probably is. Partselect.com is the greatest company to deal with. I'd recommend them to anyone and have.
Sam

When the (overpriced) replacement silverware basket arrived (rapidly, within a few days of my ordering) I was shocked and angry that the handle for the basket was not included--nor were instructions included as to how to remove the old handle from the old basket in order to fasten it to the new basket. Therefore, I spent a considerable amount of time trying to pry the handle off the old one, which was quite tricky: There were four slots which held the plastic "catches", and they had to be pushed out simultaneously. I had to fiddle with it for at least a half hour, trying various implements, until I found that I could push them out simultaneously by wedging butter knives into the slots and then easing the handle off. (I was careful to position myself so that I wouldn't slip and stab myself with the blunt butter knife.) After that, the handle snapped fairly easily into the new basket's slots.
In the end, while I was glad to be able to recycle the old handle, I wish that the basket and shelves were made more durably so they wouldn't have to be replaced, or that they could be replaced at a more reasonable price.

Turned off water at the shutoff valve. I did not turn off the power, but it is recommended you do so. I pulled the dishwasher out from under the cabinet and used a car jack to lift the front off of the ground. Disconnected the water supply and the rubber hose that fills the dishwasher tub. There are two 7mm screws that hold the water pump to the frame. If you do not have a 7mm socket, the easiest thing to use is an interchangeable screwdriver. When the screw bit is pulled out, the empty screwdriver is a 7mm. Used adjustable wrench to remove the brass water port for the supply line. Teflon tape to all connections and hooked everything back up. My supply line was old and was leaking, so I had to run out and get a new one, so that added about 30 minutes to what would have been maybe a 20 minute repair.

First, shut off the circuit that the dishwasher is on. Remove the 10 - 12 screws that secures the inside waterproof panel to the door. There are two electrical connections are either side of the handle (latch assembly) that need to be removed. No need to disconnect any other connections or reservoirs. The handle comes right out. Seat the new one in door front opening. Reconnect the electrical leads and reseat the interior panel. I would put in the 2 screws are either side of the handle first; then the 2 at the bottom on either side and then the remaining. This is a very easy DIY job.

first, i removed the inner door panel exposing the latch assembly. i then disconnected the wiring to switches noting their locations. removed and replaced with new latch assembly, connected all wiring back to their corresponding switches, assembled the inner door panel and checked to make sure the latch was working properly.

Ensure to order part # PS1559543, which is the complete assembly although the diagram doesn't show this, and not PS2100626 which doesn't include the handle. The new assembly is a different style than the original therefore you should replace the complete assembly.

This was an easy fix. Remove the eleven torque screws on the door and separate the inner door panel enough to remove the old assembly. Remove the wire connections from the door switches, reconnect to the new assembly, and reinstall the assembly and inner door panel.

After receiving the latch assembly, which arrived rather quickly, I found the handle itself was not enclosed in the package. Therefore this repair was delayed and after several calls to the 1-800 number I was informed the company had discontinued the distrubution of the handle. They offered a full refund, however I'm still waiting for the return labels so as to ship the latch back.

Now on the brighter side, the company representative put me in touch with a local distributor that did carry the latch/handle assembly as one piece and for a lot less money.

For those who are attempting the repair, don't worry, It was very simple. Just remove hex screws, lift the inside panel, unplug the two connectors and insert the new assemply.

Must say my wife was very happy to have the dishwasher up and running again.

Good luck !

Open the door and remove old basket. Place the new basket in its plave. Time elapse approximately 20 seconds

Remove the screws , opened door panel. Removed switch with latch and replaced with new parts. Replaced panel and screws. Install completed.

Pulled the removable end caps off of the sliding track that the wheels roll on and then pulled the top tray out of the dishwasher (works like a sliding drawer in your kitchen). Removed a half dozen hex screws and threw out the old wheel housing. Set the new wheel housing and new wheels in its place and re-inserted the hex screws. Slid the top tray back into the sliding track and re-inserted the end caps. Done.

Lifted out old silverware basket. Set new basket in. Took approximately 20 seconds.

take handle off old basket put on new basket done

UNSCREWED THE LOWER PART BY PLIERS AND HAND. COULDN'T UNDERSTAND WHY THE LOWER
PART WAS AVAILABLE BUT THE UPPER SPRAY ARM
WAS NO LONGER AVAILABLE WHEN THEY BOTH GO TOGETHER..