RJDW2481B Maytag Dishwasher - Instructions

with dishwasher running I would open the door and notice the lower spray arm was not turning. I removed all parts in the tub and clean off all the accumulated gunk (likely combination of food and soap scum - like a white paste) . The accumulator screens where more than 50% clogged with no way to clean the inside. I replaced the accumulator part and the lower spray arm because 2 holes had gunk in them that would not come out. dishes are now getting clean and I am switching to liquid - no more powder as I suspect it caused the build up over time.

Unfortunately, my experience was unlike that of the other people who posted. While everything did go back together it was very difficult to get it all to press down tightly enough to tighten each set of screws. The project took about 2.5 hrs and I still don't think it is exactly right. I'm still going to have a professional out to finish the job. Also, the tool needed to complete the job was nothing fancy, but also not in everyone's home tool kit.

received new basket without a basket handle; had to remove handle from old basket & attach it to new basket; took 2 separate tries to remove old handle & each try took about an hour; used screwdriver & pliers but had to be careful not to break handle; eventually used dimes to pry open & hold the attached sections of the handle open in order to free the handle from the old basket; we sure hope the new basket lasts a lot longer than the 2 years that the old basket lasted before it broke.

Troubleshooting: Noted soap dispenser full of apparently wetted soap, drying cycle dried to brick-like mess. Dishes full of soap particles, not clean. Water through floor and basement ceiling.

Pulled all racks (note arrows on ends of rack supports), used vice grips to remove bottom spray arm (better to use washcloth around little knob to protect from vice grips), unscrewed all torx fasteners to get assembly out. Had to carefully maneuver pump housing out since it attached to water distribution assy. Found stripped sleeve, but didn't understand function until I saw similar post on this site (Thanks!). Ordered seal and chopper kit, paid extra for "2 day" delivery and rx the next week due to holiday weekend (what's up with that? I ordered a linksys security camera on saturday and rx on Sunday from "Lasership"). Followed included instructions - worked fine. Note assembly order of pump with respect to water distribution assembly - I assembled and dissassembled twice due to forgetting interference.

Ordered part. (Part was larger than the original . That is it dis not fir int supports tha same as rhe original. Hut i modifird the support by assin copper wire to fanten the heater to the supports.) The instalation was no pronlem with a little engineering. Works like a charm, Wife Happy Most important result.
Elmer

I removed the main plastic bolt with a pliers and then just used a screwgun with a star tip for all the screws.
I am a 43 year old woman with no experience and I was able to figure it out. The machine cleans much better now.

Was really easy to replace just unscrew the dishwasher and remove from under the counter about 3 inches. No need to disconnect the water line or electric. Unscrew one Torx (star) screw and put the new one in. Simple, just have the screw driver before you start.

1. remove inside door panel
2. verified the part needed using partselect web site (entire latch assembly).
3. removed connecting wire sockets and replaced part and door (simple process).

I removed the inside door panel, unplugged the old assembly and replaced with the new. The only caveat is that I THOUGHT the unit came WITH a new plastic handle, and it did not. It was very difficult to remove the handle from the old unit, and to install it in the new unit. The description was not adequate. I had read other blogs and they warned of the same missing handle, and I thought I had ordered correctly. The repair is fine, but the old handle is cracked, so I dont know how long it will last.

First I made sure the breaker for the appliance was turned off!

I only had to unscrew all the screws from the inside door.

Next I used pliers to pry the old Latch Assembly (it is all pig tailed so only to plugs to undo).

Next, I snapped the new Latch Assembly into the two sockets.

Screws were replaced and wa la!

Turned breaker on and tested. Easy as pie. Took about 10 minutes from collecting the tools, fixing the problem, and replacing all the tools.

I actually had my 14 year old daughter do it so that she could learn how to make small repairs. This would have easily cost approximately $150 for a repairman to come and fix.

Then we went to the garage and unstuck the valve on the carberator to our '75 Chevy! (it was cold).

Not bad for a couple of girls!

Removed two screws at the top of the base washer. Three screws removed down both sides of the base washer. Lifted washer out enough to see the cable and spring connections. Removed cable and replaced with new and re-connected. Slid washer back into position and installed screws.

Basket Replacement very simple just remove old and set new basket in place

Pull dishwasher about 1/2 out of cabinet. Remembered to turn off power just in time. Removed electrical leads. Hand removed nuts retaining the heating element. Installed new element - hand tightened nuts.

Took out the old basket,
Threw it away.
Popped in the new baskey,
filled it with forks and spoons.
Works great!

By the way, my order arrived in one day.
Phenomenal!

I have done two repairs, and both times PartSelect.com came to the rescue! The first repair was a few years ago when the dishwasher would run but nothing got wet. It made all the right noises except the sound of water being thrown around, because no water was being pumped! This resulted from a cheap plastic "chopper" assembly that stripped and wouldn't drive the impeller. PartSelect sold me a solid metal replacement part for under $10 and that fixed the problem for several years.

Recently, we had a different problem where the dishwasher completely haulted and the wash motor wouldn't run. This was caused by a faulty impeller, another cheap plastic part. The wash impeller fragmented around the drive shaft to where it sat uneven and thus created too much resistance for the motor to drive it. I removed the impeller, superglued the plastic parts together so that I could then wrap them in copper wire (about 1mm diameter), and then I hot-glued over the copper wrapping to secure the entire thing and to help keep water out of it. I did this so that we could wash dishes while we waited for the new impeller. Well the new impeller came several days early and so far I have just been too lazy to go remove the makeshift part. I figure it will fail sooner or later and then I will install my new part which should give me at least 9 more years of trouble free washing!