WU302 Maytag Dishwasher - Instructions

Since the bimetal repair kit was not available, I bought the complete detergent cup, gasket, and bimetal switch assembly set. This was still far cheaper than paying for a professional repair. All I had to do after shutting off the power is to remove screws to open up the door (door trim/6 screws & 6 screws on the inner side of door edges to remove outer wall of door). The detergent cup assembly is right there for easy access! I unplugged the 2 electric wire plugs to the bimetal switch (paying attention to which plug goes where for when I reassemble), removed the 6 screws that mount the cup assembly, removed assembly and gasket, cleaned the surfaces, and reassembled with the new assembly. Very, very easy to do and everything works like a charm!

Removed two panels on front bottom to gain access to motor and pump pulley.
Looped belt around motor pulley and partially looped belt on larger pump pulley then turned pump pulley together with the belt until belt was fully installed., then coated belt with silicone grease to lubricate it.. very simple procedure.

One note of precaution, UNPLUG power plug before working on appliance.

Clip the plastic on to the vertical pieces. No tools needed

No tools were needed. The top rack was slid out as far as it could go (no need to remove from the dishwasher) and the utensil basket was removed. Matching the positioning of the other good clips on the upper rack, the new accessory rack pivot clips were snapped into place. The pins on each end of the accessory racks were placed into the pivot holes provided on the clips and pressed into placed. The bottom prong on each clip was then gently pressed upward until it snapped into the groove on the bottom of the clip. The pivot action of each rack was tested. The untensil basket was put back into place and the upper rack was slid back into the dishwasher. Done!

this is a portable unit
the wood top is removed this allows access to the side cabinet screws and the lower front trim screws behind the lower front trim panel you can access the hose connections disconnect and reinstall
new part works great!

Very simple. Remove bottom panels. Remove one screw holding old switch in place. Move wire connections from old switch to new one. Cleaned and lubed the switch actuator. Mounted new switch. Checked that float and actuator worked freely. Left bottom panels off till I ran a load - just to be sure all was OK. Remount bottom panels...Done! P.S. Don't forget to turn power off to dishwasher any time you work on it!!

followed the scematic on the wesbite that i used to i.d. the repair part needed. removed the front door outside cover (8 screws) removed the bi-metal switch (2 screws), did not need to replace the door latch or spring. replaced the switch and the front door cover and ran the dishwasher to test the new switch. worked fine and has been working fine.

I was not able to follow the instructions exactly since they called for stretching the belt around the back pulley with the left hand. For a woman that prooved too difficult so instead I attached the belt to the back pulley first and used 2 screw drivers (they are thin) to stretch the belt around the front pulley. It took considerable effort but I got it on!! The dishwasher now works. Praise God!!

First, I had to remove the outer face panel of the door. Four screws on the inside of the door hold the large panel onto the front. Removing these screws and the panel revealed the detergent cup assembly. There is no need to disconnect the power as long as the door latch is in the open position for this repair. I removed the two wires, blue and white from the leads, keeping note which was attached to which lead. I used a hex head screw driver to remove the 6 screws that hold the detergent cup in place. After removing the detergent cup and gasket, I cleaned the surfaces with a scouring pad to make sure the new gasket would have a good seal. I installed the new detergent cup with the 6 hex screws and re-attached the leads. I replaced the face panel with the four interior screws after running a couple cycles to be sure the problem was fixed, which it was.

remove 3 screws from either side door edge trim : Note ! panel "notches" are up : remove both original panals plus the cardboard spacer : swap only the old color with the new one and reinstall spacer cardboard and be sure it stays centered : remember panel notches are up : carfully slide the panels over the spacer cardboard while keeping the cardboard centered : becareful panel edges can scratch in the door trim : Note! opposite side door trim can be removed if needed .

Had to loosen the drive motor enough to slip the belt around the pulleys. The only problem was the amount of space available to work in.

It was my first dishwasher belt and it was much tighter than I thought it was going to be. I was worried I was going to break it putting it on so I was a bit stumped, but finally got it on and its good as new.

1. Removed the four screws to remove the door front.
2. Removed the six screws to remove the detergent cup.
3. Replaced bimetal strip, cam, and spring. (simple task)
4. Replaced gasket and seal.
5. Replaced detergent cup.
6. Replaced door front.

Very easy,take off the old faucet screen and screw on the adapter. What I really liked was the ease of ordering the part. In less than 5 minutes I had located the part and ordered it. Less than 3 days later, I had the part. Way to go PartSelect.

Took off bottom cover. Put belt on center housing than put belt on moter pully.Rolled belt down onto center pully while turning pully clockwise. Popped right on.