MDB8951AWW Maytag Dishwasher - Instructions

My married daughter actually did the repair. I removed the plastic assemblies that held the upper cage and upper spray assembly. She unscrewed the screws that held the filter/impeller assembly in place and replaced the old one with the new one. I finished the job by cleaning the interior of the washer and putting everything back together. The dishes are sparkling clean again!

It is such an easy snap-on repair that a child could do it. I am grateful that your company had a picture so I could compare my broken part with the ones you guys have as I couldn't find my model number. I took my time to do the job right, so it took me almost 15 seconds! lol

with dishwasher running I would open the door and notice the lower spray arm was not turning. I removed all parts in the tub and clean off all the accumulated gunk (likely combination of food and soap scum - like a white paste) . The accumulator screens where more than 50% clogged with no way to clean the inside. I replaced the accumulator part and the lower spray arm because 2 holes had gunk in them that would not come out. dishes are now getting clean and I am switching to liquid - no more powder as I suspect it caused the build up over time.

I followed the you tube video exactly. Very easy to do. I did not tighten the screws sequentially as shown in the video, rather I did the opposite ones to make sure nothing was skewed. Very easy, about 20 minutes.

received new basket without a basket handle; had to remove handle from old basket & attach it to new basket; took 2 separate tries to remove old handle & each try took about an hour; used screwdriver & pliers but had to be careful not to break handle; eventually used dimes to pry open & hold the attached sections of the handle open in order to free the handle from the old basket; we sure hope the new basket lasts a lot longer than the 2 years that the old basket lasted before it broke.

You just remove the old unit and set in the new unit. the wheels were already connected.

I know that I have very hard water, but am reluctant to get a softener. I hope that changing the "guts" of the water delivery to my dishwasher will help...already replaced the filters which helped too... so far, it's a little better.

Installation was a breeze. Took off the upper, middle and lower spray arms. Had to loosen screws in filter assembly to remove old manifold. Popped everything into place... had to scrape mineral deposits off clips that support manifold and upper spray arms.
Easy...

Troubleshooting: Noted soap dispenser full of apparently wetted soap, drying cycle dried to brick-like mess. Dishes full of soap particles, not clean. Water through floor and basement ceiling.

Pulled all racks (note arrows on ends of rack supports), used vice grips to remove bottom spray arm (better to use washcloth around little knob to protect from vice grips), unscrewed all torx fasteners to get assembly out. Had to carefully maneuver pump housing out since it attached to water distribution assy. Found stripped sleeve, but didn't understand function until I saw similar post on this site (Thanks!). Ordered seal and chopper kit, paid extra for "2 day" delivery and rx the next week due to holiday weekend (what's up with that? I ordered a linksys security camera on saturday and rx on Sunday from "Lasership"). Followed included instructions - worked fine. Note assembly order of pump with respect to water distribution assembly - I assembled and dissassembled twice due to forgetting interference.

I watched a couple of videos on Youtube, and for once it was actually easier than anticipated. Unplug unit. Remove door screws. Separate inner door from outer door. Remove connector from dispenser (needed flat blade screwdriver to pry it at first.) Remove six screws holder dispenser in. Removed old dispenser, inserted new one, tightened six screws, re-connected wires, attached inner door to outer door, and was done in literally less than 10 minutes. Note: I was using a battery powered screw driver to remove the screws, so that's one reason why it went so fast.

1. remove inside door panel
2. verified the part needed using partselect web site (entire latch assembly).
3. removed connecting wire sockets and replaced part and door (simple process).

remomed old adjuster and attached the new one to the housing and it was done it was very simple

First I made sure the breaker for the appliance was turned off!

I only had to unscrew all the screws from the inside door.

Next I used pliers to pry the old Latch Assembly (it is all pig tailed so only to plugs to undo).

Next, I snapped the new Latch Assembly into the two sockets.

Screws were replaced and wa la!

Turned breaker on and tested. Easy as pie. Took about 10 minutes from collecting the tools, fixing the problem, and replacing all the tools.

I actually had my 14 year old daughter do it so that she could learn how to make small repairs. This would have easily cost approximately $150 for a repairman to come and fix.

Then we went to the garage and unstuck the valve on the carberator to our '75 Chevy! (it was cold).

Not bad for a couple of girls!

Our dishwasher broke just before the big Christmas dinner! We ordered the matching part from your website and rush delivered it. We then removed the old part with a screw driver and replaced it with the new part. It fit perfectly and the dishwasher was back in operation. Christmas was saved!
Thank you!

I removed the inside door panel, unplugged the old assembly and replaced with the new. The only caveat is that I THOUGHT the unit came WITH a new plastic handle, and it did not. It was very difficult to remove the handle from the old unit, and to install it in the new unit. The description was not adequate. I had read other blogs and they warned of the same missing handle, and I thought I had ordered correctly. The repair is fine, but the old handle is cracked, so I dont know how long it will last.

I removed the main plastic bolt with a pliers and then just used a screwgun with a star tip for all the screws.
I am a 43 year old woman with no experience and I was able to figure it out. The machine cleans much better now.