MDB6657AWB Maytag Dishwasher - Instructions

First you must understand that the end cap is not a solid piece. The plastic facing you is wrapped over the piece behind it. The separation may be obscured by age. Wedge thin bladed screwdriver into the outside edge of end cap at the bid point, a sturdy hunting knife will probably work better. When you hit the seam, pry it apart and fold it back. Unwrap the part and repeat on other side. The dishracks will easily slide out and in.

Snapped old ones off and snapped new ones on.

First I removed the inside door panel, then I snapped the old latch out and put the new latch on with screws. Easy, and works perfect now.

I simply looked at the other side (which was still functioning) and put the new one on but in reverse (left side/right side) I also was missing the end stop to the slide and simply popped that in and snapped closed. Two simple parts and 15 mins. solved a whole lot of aggrivation,
without any aggravation! wish I had found this site sooner!

my husband took the bottom rack out, unscrewed it where there were screws, lifted up the unscrewed part, took the filter out,cleaned out any gunk, replaced the filter put the part back on, rescrewed it, put the rack back in and it works much better.

The most difficult part is learning how to unsnap the plastic retainers at each end of the steel sliders on each side of the dish rack. Push the end caps to the outside and the plastic inserts will snap open and slide off the ends of the rails in two pieces (note how they were oriented so you can replace them later). The caps must be removed from both ends of each rail. Slide out the basket. slide the rails out. Pull the old rollers off the pins. Place the new rollers into position. A smart rap with the palm of your hand should snap the rollers onto the pins. If you have done it correctly, the rollers will not pull off the mounting pins. You could also place a small block of wood against the roller and use your hand or a small hammer or weight to snap the pins into place. Assemble in reverse order.

Excellent site. When the dishwasher started making a loud grinding sound, i thought "oh great -- now I'll have to buy a new one". After searching the internet (I just entered the model number of my Maytag dishwasher), Partsselect.com came up in the search results. I read several postings from previous customers which described the same problem I was having... followed their step-by-step instructions and was able to disassemble the lower washer arm and find the culprit -- a broken wash impeller. Ordered the parts, they arrived within a couple of days, spent 15 mins putting everything back together and I'm now good to go! THANKS PARTS SELECT!!!!! I owe somebody a free lunch!

i removed the strainer cover and then removed the discharge assembly. then repeated steps to finish.. parts select was very fast and cheap ordered ontuesday and arrived on thursday. I will recomend parts select to all

Had service man: stated I would need new motor/pump at $400 complete. I didn't like the interior of new dishwashers. Nothing to lose, so I verified that the motor was working; reviewed short PartSelect video. Ref: very helpful PartSelect assembly diagrams with parts list. THANKS PS! Removed two dish racks (top rack: extend fully and flip the roller-keeper clips. Pull rollers and rack-pins apart) Then I started taking the pump apart all the way down to the pump base (fits into tub with seal - did not replace that seal). Very intuitive - some parts are tight and must be encouraged to come apart; take care of seals and o-rings; take notes of sequence if necessary. Look for parts requiring replacement. Unscrew Spray Tower Lower Extension Nozzle and lift off Spray Arm and two lower spray arm seals - check seals for wear. Unscrew pencil-like Spray Arm Support Nut. Cause: I found a totally-clogged Pump Housing Filter, a bit of steel wool about the size of my thumb (same size as water supply opening in bottom), and small piece of broken glass. Cleaned all parts coated with lime; new Pump Housing Filter (could not clean adequately). Cleaned the screens underside of filter support (difficult) with brush and wire. Replaced o-rings for Wash Impeller and Drain Impeller as a matter of principle. Only alignment requirement is with bottom water supplly hole. Everything works like new now! Recommendation: clean Pump Housing Filter annually.

Ordered 3 parts first ..all came within two biz days..forgot the toe panel, called it was here the next day! The people that assisted me were wonderful! My husband did the repair. the dishwasher looks like new!!!!! I will order from Part Select again and again...extremley pleased. Now if only we could cover the Refrigerator in Black it would look like a whole new kitchen!

Took out the old basket,
Threw it away.
Popped in the new baskey,
filled it with forks and spoons.
Works great!

By the way, my order arrived in one day.
Phenomenal!

I decided to do some regular maintenance on the dishwasher. The spray arm and components have been caked from our hard water and soap. I unwittingly broke the seal on a portion of the spray arm to try and clean. I did not know it was sealed, thought it could snap. The broken seal created a high pressure stream that pushed the door enough to let water leak out.

Replacing it was easy. Unscrewed the plastic nut, lifted out spray arm and disc, unsnapped arm from disc and replaced new one. Leak is now fixed. This part was much much cheaper than i imagined and brought new life to our dishwasher. Best.Store.Ever.

Snapped in the new part!

I TOOK THE INSIDE PARTS ABOVE THE MOTOR APART AND TRIED TO CLEAN ALL THE CALCIUM AND MINERAL DEPOSITS THAT WERE PRVENTIN WATER FROM GETTING THROUGH. THERE WAS A LOT OF CALCIUM. MOST OF IT i WAS ABLE TO CLEAN AFTER A LOT OF SCRAPING AND SOAKING IN VINEGAR AND CLR. THE VINEGAR WAS THE MOST EFFECTIVE OF THE TWO.
i BROKE THE FILTER GUARD WHEN I TOOK IT APART. I SHOULD HAVE CHECKED ONL.INE BEFORE i START IT. THE SECONDARY FILTER ASSEMBLY WAS TO FAR GONE DUE TO MY MISHANDLNG AND HEAVY DEPOSITS INSIDE THE FILTERS. PUTTING IT BACK WITH THE NEW PARTS WAS EASY BUT I HAD TO SUBSITUTE SCREWS BECAUSE THE ORIGINAL ONES WOULD NO LONGER HOLD TWO PARTS TOGETHER. THE PARTS WERE LEAKING TO MUCH WATER. ONCE I HAD IT BACK TOGETHER THE SECOND TIME IT WORKED FINE. HOWEVER I HAD REALIZED THAT THE O-RING WAS NOT MISSING (MY BAD EYES DID NOT SEE IT IN PLACE AND SO I THOUGHT I HAD LOST IT). i EMAILED PARTS SELECT FOR A RETURN AUTHORIZATION BUT NEVER HEARD BACK FROM THEM. MAYBE I NEED TO GIVE THEM A FEW MOR DAYS. THE O-RING COST $3.76 AND MY WIFE WILL NOT BE HAPPY TIL I GET THAT BACK. PARTS SELECT DIAGRAM AND PARTS PHOTOS AND ANOTHER WEBSITE WERE A BIG HELP..

Changing the valve only took about 30 minutes but reusing the fitting from the old valve I could not get it to stop leaking on the copper side of the fitting. I ended up going out and getting a new fitting and cutting the copper line to make a new connection. Then the problem was solved.