DWC7602ABB Maytag Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- E L from Seeley Lake, MT
- Parts Used:
- WPW10117748
- Difficulty Level:
- Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Leaking at bottom of door
The initial repair was more involved due to figuring out how to get at the problem. A foam sealer strip located at the bottom of the inner door had lost it's seal. I first sent off for one and it was of relatively thin material. It was carefully installed but still leaked. I ordered another one from Part Select and it had thicker foam. It was installed right over the previously installed strip and made a tight seal. (knock on wood)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Chebanse, IL
- Parts Used:
- WPW10254672
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I had bought the portable dishwasher from an add in the paper and unfortunately I was unaware that they require faucet adapters and it was not given to me along with the appliance.
I ordered the part and it fit perfectly!! About five minutes to screw it onto my faucet and problem solved!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Pottstown, PA
- Parts Used:
- Y912547, WP99001291, 99001289, WP99001287, WP902899
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
Dispenser lid would not open
The wax motor seemed to work.
At first I thought something was broken and I tried to figure out the "theory of operation" Working the actuator of the wax motor, I COULD NOT GE THE LATCH TO MOVE THE WAY I THOUGHT IT SHOULD. I ASSUMED EITHER IT WAS BROKEN IN SOME WAY I COULD NOT DETECT OR THERE WAS A FLAW IN ITS DESIGN!
It took a long time to figure out the latch would not be worked open unless it was actually holding the lid- this positions the latch at "half mast" and allows the mechanism to "pick it up from there" and open the rest of the way. So once I figured that out, I concluded the failure was really just worn out parts that were out of tolerance for how this "half mast" position and opening was supposed to work. So I ordered all fresh pieces just to be sure, assembled it (very easy) and put it in (easy). It all works fine now.
At first I thought something was broken and I tried to figure out the "theory of operation" Working the actuator of the wax motor, I COULD NOT GE THE LATCH TO MOVE THE WAY I THOUGHT IT SHOULD. I ASSUMED EITHER IT WAS BROKEN IN SOME WAY I COULD NOT DETECT OR THERE WAS A FLAW IN ITS DESIGN!
It took a long time to figure out the latch would not be worked open unless it was actually holding the lid- this positions the latch at "half mast" and allows the mechanism to "pick it up from there" and open the rest of the way. So once I figured that out, I concluded the failure was really just worn out parts that were out of tolerance for how this "half mast" position and opening was supposed to work. So I ordered all fresh pieces just to be sure, assembled it (very easy) and put it in (easy). It all works fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mark from Waterbury, DC
- Parts Used:
- 12001489
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
noisey poor cleaning
Everyone said it's too old to fix, I said I have nothing to lose by taking it apart and looking for broken parts.Sure enough I found a broken pump propeller and orded the part and had it in 18 hrs. I,with the help of a you-tube tutorial, fixed it in an hour. My wife thinks I am a hero. I think I am a hero cause I saved $500.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- phillip from hodges, AL
- Parts Used:
- 99002531, WP99002363, 912014, WP911265
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
float leaking
float was missing palnut and letting the float slide up too much causing small leak around the float
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Wharton, TX
- Parts Used:
- WP903404, WP902894, WPW10254672
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Faucet connection leaking, door leaking
Use towels to catch water that spills from unit. Lay unit on side to expose bottom. Remove plastic retainers, rear wheels, and bottom cover. Disconnect inlet and discharge hoses. Tie pull cord onto each hose separately. Temporarily re-install rear wheels. Set uinit upright. Remove two star screws from underside of wooden top. Slide top forward to release and remove top. Remove tie strap holding hoses to inner bracket. Lay unit on side again and pull hoses out. Remove discharge hose first to allow removal of inlet hose from plastic housing on back of unit. Tie pull cords to new hoses. Pull new hoses into unit. Reconnect hoses. Turn unit upright. Replace tie strap on bracket with new hoses. Hoses are marked as to where they should be secured to the bracket. Replace top. Remove old door gasket by pulling from one end of gasket. Clean gasket groove. Push new gasket into place. Close door to seat gasket. Remove and replace faucet adapter kit. Run unit and check for leaks. Lay unit on side, remove rear wheels, replace bottom cover and plastic retainers, reinstall rear wheels.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marge from Cranford, NJ
- Parts Used:
- WP6-918873
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The basket in our dishwasher had many broken parts on the bottom and the silverware kept falling through
We were happy to find the basket we needed listed on your website, even after we could not find it on the Maytag site. It was perfect. I can't believe we lasted almost 2 years with the broken basket we had.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aimee from Mount Pleasant, MI
- Parts Used:
- WP902894
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door was leaking badly
After performing some maintenance to get the water flowing properly through the system (that's another story) the door was leaking very badly during any test run of the dishwasher.
We thought it was the gasket because the old one was calcified and dried out from years of harder water.
We ordered the new one and in minutes after receiving the new gasket we had a firm seal and our dishwasher was back in action.
We thought it was the gasket because the old one was calcified and dried out from years of harder water.
We ordered the new one and in minutes after receiving the new gasket we had a firm seal and our dishwasher was back in action.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from South Huntington, NY
- Parts Used:
- 99002254
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dishwasher would not work unless the door was held in with pressure.
I removed the screws on the inside of the door. Removed the cover and changed door switch and holder and put the new one in. Replaced the cover
all in less than half an hour.
all in less than half an hour.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Clarkston, MI
- Parts Used:
- WPW10117748
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
water was dripping from the bottom of the front loading door. Over time this had seeped into the insulation foam strip and formed a solid encrustation within the foam strip.
The real cause of the leak had nothing to do with the foam strip. The latch for the front loading door at the top needed to be adjusted to hold the door in tighter to the rubber door seal. This simple adjustment stopped the leak but since the foam seal was all encrusted with dried detergent from probably years of absorbing the leak, I replaced it with your new foam strip. I used a screw driver with torx bit and removed the stainless screws holding the inner door to the outer door. Once these were separated I removed the old foam strip using a putty knife and lacquer thinner. Placing the new strip onto these cleaned surfaces was the easiest part of the whole repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Brooks, GA
- Parts Used:
- 912529
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Pump gasket had deteriorated with age and causing odors.
The dishwasher is well engineered to perform this work.
Remove the bottom two panels to provide access and visibility to base of pump motor.
Locate plastic pump locking lever and push toward rear of DW to unlock pump from DW.
Inside the DW remove basketsand spray arms. Revove screws holding cover over pump motor and remove cover.
From below raise pump motor and support with block (piece of 2x4 worked well).
insde DW, removre old gasket, clean well around pump and botom of DW, install new gasket.
From below remove block to drop pump motro back into place, and re-tighten locking lever by pull toward you.
re-assemble inside componets, run through a rinse cycle to test for leaks and replace bottom panels.
I
Remove the bottom two panels to provide access and visibility to base of pump motor.
Locate plastic pump locking lever and push toward rear of DW to unlock pump from DW.
Inside the DW remove basketsand spray arms. Revove screws holding cover over pump motor and remove cover.
From below raise pump motor and support with block (piece of 2x4 worked well).
insde DW, removre old gasket, clean well around pump and botom of DW, install new gasket.
From below remove block to drop pump motro back into place, and re-tighten locking lever by pull toward you.
re-assemble inside componets, run through a rinse cycle to test for leaks and replace bottom panels.
I
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from Topeka, KS
- Parts Used:
- WP903297
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Broken wheel, broken fingers
The rear right caster (wheel) under our fairly new portable dishwasher broke. Upon looking up the part, I discovered that it did not bolt into place, meaning that the exterior skin of the dishwasher did not have to be removed and that more than likely I could fix it myself.
The replacement wheels from Partselect were nicer quality than what the original was and showed up just two days after they were ordered.
However, getting what remained of the broken caster out was frustrating. I am not unhandy around the house, having put in two new bathrooms and a staircase.
But after yanking and prying on the broken caster for 20 minutes (slamming my fingers into the floor every time the pliers slipped), I could see where most people would give up and call a repairman. Finally, with help from small pry bar, the broken caster popped loose. Thankfully, putting the new in was as simple as sliding it into place.
Unfortunately, after all that work, we discovered the new caster was slightly taller than the old, leaving the dishwasher with a distinct wobble that my wife said was unacceptable. She, of course, had not been repeatedly introducing her hand to the floor.
I had ordered two replacement casters, thinking that another of the originals might break. But getting the second one out proved just as difficult as the first, even with the help of the pry bar.
After much cussing and kissing of finger booboos, our Maytag dishwasher is as good as the day we brought it home.
The replacement wheels from Partselect were nicer quality than what the original was and showed up just two days after they were ordered.
However, getting what remained of the broken caster out was frustrating. I am not unhandy around the house, having put in two new bathrooms and a staircase.
But after yanking and prying on the broken caster for 20 minutes (slamming my fingers into the floor every time the pliers slipped), I could see where most people would give up and call a repairman. Finally, with help from small pry bar, the broken caster popped loose. Thankfully, putting the new in was as simple as sliding it into place.
Unfortunately, after all that work, we discovered the new caster was slightly taller than the old, leaving the dishwasher with a distinct wobble that my wife said was unacceptable. She, of course, had not been repeatedly introducing her hand to the floor.
I had ordered two replacement casters, thinking that another of the originals might break. But getting the second one out proved just as difficult as the first, even with the help of the pry bar.
After much cussing and kissing of finger booboos, our Maytag dishwasher is as good as the day we brought it home.
Was this instruction helpful to you?
Thank you for voting!
Detergent cup lid not opening during cycle
Suspecting the problem was a sticky gasket on the old detergent cup lid, I replaced the lid.
First remove the old lid by pushing one of the hinge pins (the one without a spring) out of the cylinder hole in the dishwasher door. Important: before completely removing the lid, note how the spring is installed on the other pin. Then, simply install the new lid and spring and push the non-spring pin back into the cylinder hole in the DW door.
My dishwasher now works fine! :-)
First remove the old lid by pushing one of the hinge pins (the one without a spring) out of the cylinder hole in the dishwasher door. Important: before completely removing the lid, note how the spring is installed on the other pin. Then, simply install the new lid and spring and push the non-spring pin back into the cylinder hole in the DW door.
My dishwasher now works fine! :-)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Lomax, IL
- Parts Used:
- WP903404
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
badly damaged gasket
the coupling for the water hookup for my rollaway dishwasher was very badly damaged. After looking everywhere including authorized dealer and repair places, on-line at the manufactures parts website, I finally broke down and ordered the entire hose assembly. When it arrived, I simply used a toothpick to carefully remove the new gasket from the new part and put in the the old one. It took about 30 seconds and works perfectly. I paid 60 bucks for a tiny little washer, but I have an extra hose assembly if something should go wrong in the future.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Owasso, OK
- Parts Used:
- WP6-918873
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
silverware basket broken - replaced with new one
I was able to remove the old handle and place it on the new basket - using only a screw driver.
Was this instruction helpful to you?
Thank you for voting!