MDB8951AWS Maytag Dishwasher - Instructions

The old docking station seals were getting very soft. To put a band aid on the wound until the new docking station got here I put a sleve on the washer bar feeder tube. This made an improvement. The docking station was removed using a screw driver to unsnap the station. Then all I had to do was snap the new one in. Be care ful not to pull on the piece the docking station is snapped on to. There are metal clips behind there that hold that water delivery tube on to the back of the dishwasher. Those clips are twisted on and can be striped off easily by pulling strait towards you. If that happens you must secure the clips using self tapping screws and a water proof sealent.

Pull dishwasher about 1/2 out of cabinet. Remembered to turn off power just in time. Removed electrical leads. Hand removed nuts retaining the heating element. Installed new element - hand tightened nuts.

Four screws were removed and new parts were installed. The only problem was that two types of rack adjusters exist. If your dishwasher does not have a lever, part number PS2100470, then the new rack adjuster either left or right side will not work without part numbers PS2100470(lever) and PS2100308(cover). Be sure to order parts for both sides since the original plastic wheel supports have been replaced with steel.

I have done two repairs, and both times PartSelect.com came to the rescue! The first repair was a few years ago when the dishwasher would run but nothing got wet. It made all the right noises except the sound of water being thrown around, because no water was being pumped! This resulted from a cheap plastic "chopper" assembly that stripped and wouldn't drive the impeller. PartSelect sold me a solid metal replacement part for under $10 and that fixed the problem for several years.

Recently, we had a different problem where the dishwasher completely haulted and the wash motor wouldn't run. This was caused by a faulty impeller, another cheap plastic part. The wash impeller fragmented around the drive shaft to where it sat uneven and thus created too much resistance for the motor to drive it. I removed the impeller, superglued the plastic parts together so that I could then wrap them in copper wire (about 1mm diameter), and then I hot-glued over the copper wrapping to secure the entire thing and to help keep water out of it. I did this so that we could wash dishes while we waited for the new impeller. Well the new impeller came several days early and so far I have just been too lazy to go remove the makeshift part. I figure it will fail sooner or later and then I will install my new part which should give me at least 9 more years of trouble free washing!

I'm telling this story for my husband who is a pretty handy guy--I watched him do the repair. I had had someone out to look at the dishwasher and they said it would be $284 to fix this one little thing because you couldn't buy the one little part separately, you had to buy a whole new motor. Since the dishwasher is old, it didn't make sense to invest this much in it--might as well buy a new one for that kind of money. My husband did some looking around and found the part on your site and installed it himself. So the cost was under $40. The dishwasher is now working better than it had been for a while.

Slipped it on the upper rail.

Took a while to figure out what had to be done. Brackets have to go under the metal frame which involves dropping the compartment. That is done by removing the screws which are hidden under the door gasket. Once I knew what had to be done it was simple.

Removed all the screws holding the inside panel of the door to the door itself. Lifted out the old broken door latch. Pulled the wire clips from the 2 switches located on either side if the door Latch assembly. This is a bit difficult. You have to keep working the wire clips back & forth; Up & down until the clips are free from the switch metal contacts. Reinstall the wire clips on the new door Latch assembly making sure you attach the black wires and white wires on the same side of the new latch assembly as on the one removed. Replace the new latch assembly aligning the mounting holes on the door with the new latch holes. Replace the inside panel aligning the holes and replace the screws. The screws were the star head type so you need a special driver bit. I used the box the latch came in the prop up the inside door panel while I worked.

Remove the water distributor, filtration plastic parts down to the base of the tub and clean of debris. Sometimes a small piece of plastic from the upper glass tray can break off and find its way into the bottom. Once its cleaned this section and be put back. Had to remove the unit from the cabinet and replace the drain motor and also cleaned the drain hose that runs to the garbage disposal. Most times this problem is caused by a blocked drain line or debris in the bottom of the tub constricting waster water from getting into the drain motor.

Easy! Unscrewed panel, took off old latch, put on new. Took about five minutes.

Took old one out And placed new one in dishwasher.

opened door---- took out old basket--threw it away. set new basket in its place!!!!

Snapped new wheel on

Ordered a new basket. Tossed out the old one. Done

Remove the screws , opened door panel. Removed switch with latch and replaced with new parts. Replaced panel and screws. Install completed.