MDB9150AWQ Maytag Dishwasher - Instructions

Turned off power to the washer. Removed the inside door cover. Removed the old board, carefully noting wire connections. (Take a photo of old board at the beginning, if you feel insecure about this.) Installed new board, carefully plugging wire connectors as they had been on old board. Replaced inside door cover. Restored power to washer. Conducted a test run. THE WASHER WORKS!!
By the way, I received the new board two days after ordering it. Now, that's service!

Ordered BOTH the front and rear tines as the front tine showed some superficial rust through the plastic covering in a couple of spots. Re-used the tine holders which were still solid condition and flexible. Snapped bowl holder tine unit out of dishwasher, snapped new tines in place, snapped unit back in dishwasher. Took 5 minutes or less. All other parts of the dishwasher rack were still in excellent condition with no cracked spots on the vinyl covering or rusted spots visible anwhere.

unscrew screen and cover and unbolt impeller replace with new parts. everything goes back together easily, anyone with even minimal repair skills should be able to do this repair.

i removed the strainer cover and then removed the discharge assembly. then repeated steps to finish.. parts select was very fast and cheap ordered ontuesday and arrived on thursday. I will recomend parts select to all

my husband took the bottom rack out, unscrewed it where there were screws, lifted up the unscrewed part, took the filter out,cleaned out any gunk, replaced the filter put the part back on, rescrewed it, put the rack back in and it works much better.

had to fiddle around just a bit to look at the others and see how these fit in. No tools were required - just snapped into place once I figured them out.

The most difficult part is learning how to unsnap the plastic retainers at each end of the steel sliders on each side of the dish rack. Push the end caps to the outside and the plastic inserts will snap open and slide off the ends of the rails in two pieces (note how they were oriented so you can replace them later). The caps must be removed from both ends of each rail. Slide out the basket. slide the rails out. Pull the old rollers off the pins. Place the new rollers into position. A smart rap with the palm of your hand should snap the rollers onto the pins. If you have done it correctly, the rollers will not pull off the mounting pins. You could also place a small block of wood against the roller and use your hand or a small hammer or weight to snap the pins into place. Assemble in reverse order.

I simply looked at the other side (which was still functioning) and put the new one on but in reverse (left side/right side) I also was missing the end stop to the slide and simply popped that in and snapped closed. Two simple parts and 15 mins. solved a whole lot of aggrivation,
without any aggravation! wish I had found this site sooner!

Took out the old basket,
Threw it away.
Popped in the new baskey,
filled it with forks and spoons.
Works great!

By the way, my order arrived in one day.
Phenomenal!

First you must understand that the end cap is not a solid piece. The plastic facing you is wrapped over the piece behind it. The separation may be obscured by age. Wedge thin bladed screwdriver into the outside edge of end cap at the bid point, a sturdy hunting knife will probably work better. When you hit the seam, pry it apart and fold it back. Unwrap the part and repeat on other side. The dishracks will easily slide out and in.

Excellent site. When the dishwasher started making a loud grinding sound, i thought "oh great -- now I'll have to buy a new one". After searching the internet (I just entered the model number of my Maytag dishwasher), Partsselect.com came up in the search results. I read several postings from previous customers which described the same problem I was having... followed their step-by-step instructions and was able to disassemble the lower washer arm and find the culprit -- a broken wash impeller. Ordered the parts, they arrived within a couple of days, spent 15 mins putting everything back together and I'm now good to go! THANKS PARTS SELECT!!!!! I owe somebody a free lunch!

Had service man: stated I would need new motor/pump at $400 complete. I didn't like the interior of new dishwashers. Nothing to lose, so I verified that the motor was working; reviewed short PartSelect video. Ref: very helpful PartSelect assembly diagrams with parts list. THANKS PS! Removed two dish racks (top rack: extend fully and flip the roller-keeper clips. Pull rollers and rack-pins apart) Then I started taking the pump apart all the way down to the pump base (fits into tub with seal - did not replace that seal). Very intuitive - some parts are tight and must be encouraged to come apart; take care of seals and o-rings; take notes of sequence if necessary. Look for parts requiring replacement. Unscrew Spray Tower Lower Extension Nozzle and lift off Spray Arm and two lower spray arm seals - check seals for wear. Unscrew pencil-like Spray Arm Support Nut. Cause: I found a totally-clogged Pump Housing Filter, a bit of steel wool about the size of my thumb (same size as water supply opening in bottom), and small piece of broken glass. Cleaned all parts coated with lime; new Pump Housing Filter (could not clean adequately). Cleaned the screens underside of filter support (difficult) with brush and wire. Replaced o-rings for Wash Impeller and Drain Impeller as a matter of principle. Only alignment requirement is with bottom water supplly hole. Everything works like new now! Recommendation: clean Pump Housing Filter annually.

Snapped old ones off and snapped new ones on.

Never having repaired a dishwasher before, I disassembled everything I dared to until I found the root of the problem--part of the impeller had broken into several little bits. It wasn't apparent where the pieces came from, but the on-line diagrams and product photos helped. The broken impeller didn't want to come off the shaft, so I just crunched it up with a pair of vise grips. That seemed to be the gentlest solution for the pump bearings. The bits of impeller also took out the pump housing, which I could have ordered with the impeller had I been more observant. [insert four more days of washing by hand here] Inspect all parts for damage and clean out all stray chunks of food and plastic before reassembling!

removed old and broken and replaced. The best part was, the turn around time from partselect. The fastest delivery of anything I ordered that part a 2 in the afternoon and had it the NEXT day, without specifiying any extra rush shipping. Right part too! Amazing job! Thanks