MDB6650AWB Maytag Dishwasher - Instructions

New pump housing filter was needed as the old one was plugged and distorted.

I

Basket Replacement very simple just remove old and set new basket in place

I reversed the tub wheel, cut off the protruding flanges so that the end of the axel pin was exposed. Then using a small socket I placed a split washer over the end of the pin, used the socket to hold the washer in place and tapped it into place with a hammer. Note there is a grove around the circumference of the pin which holds the split washer. This locked the tub wheel onto the pin and it still rolled freely. Unconventional but it worked great.

I discovered that, except for the central tower, all the spray holes were all plugged with I took to be calcium deposites . Using the parts diagram located on this web site, I removed parts. All parts can be removed either by hand, nutdriver or small wrench however you do need a star drive (simliar to an allen wrench) to remove the Pump Cover and Secondary Filter. The Lower Spray Arm unsnaps from the Pump Cover and Secondary Filter. I laboriously removed the deposits from each part down as far as the support filter. The upper spray arm can be removed by unsnapping the hub. the Pump Cover and Secondary Filter is a closed unit so. I purchased a new one. The process is very labor intensive. Next time I am going to consider purchasing all new parts or calling a repair man.

took off the inside of the door. reattached new handle, and reset the door. easy after I determined how the handle assembly worked.

Repair was really quick and simple. Found the part online easily with the information on the website I was confident it would be the right part. Recieved the part in 2 days and snapped it into place. Very satisified!

unscrew screen and cover and unbolt impeller replace with new parts. everything goes back together easily, anyone with even minimal repair skills should be able to do this repair.

Replaced with the new basket. However, the part had been replaced, and I do not like the new setup. One basket has been replace with 2 that are hooked together. Each basket has a cover, but it covers the whole side, not just a part. In my old basket, I had a part of the basket with a cover that could hold plastic lids and measuring spoons that can easily wash out of the basket and hit the heating element on the bottom. My "fix" was to remove both lids and use the lid from the old basket to cover one part of the new basket. It's not very satisfactory, as it is not hinged and had to be removed and tucked in each time!

I watched a couple of videos on Youtube, and for once it was actually easier than anticipated. Unplug unit. Remove door screws. Separate inner door from outer door. Remove connector from dispenser (needed flat blade screwdriver to pry it at first.) Remove six screws holder dispenser in. Removed old dispenser, inserted new one, tightened six screws, re-connected wires, attached inner door to outer door, and was done in literally less than 10 minutes. Note: I was using a battery powered screw driver to remove the screws, so that's one reason why it went so fast.

Shut off the water and electric then removed the cover at the bottom then removed the water inlet valve and replaced it with the new one. Turned on water and electric. Replaced cover at bottom. Very easy and the part was shipped quickly. No problems and the dishwaser works great now!!

I simply looked at the other side (which was still functioning) and put the new one on but in reverse (left side/right side) I also was missing the end stop to the slide and simply popped that in and snapped closed. Two simple parts and 15 mins. solved a whole lot of aggrivation,
without any aggravation! wish I had found this site sooner!

Removed the screws to the front panel along the inside of the door. Replaced the broken part with the new one. The only glitch was I needed a screwdriver to pry one end of the new part to seat into the hole where its installed. Replaced the screws. Job complete in 15 mins.

First I removed the inside door panel, then I snapped the old latch out and put the new latch on with screws. Easy, and works perfect now.

First you must understand that the end cap is not a solid piece. The plastic facing you is wrapped over the piece behind it. The separation may be obscured by age. Wedge thin bladed screwdriver into the outside edge of end cap at the bid point, a sturdy hunting knife will probably work better. When you hit the seam, pry it apart and fold it back. Unwrap the part and repeat on other side. The dishracks will easily slide out and in.

Snapped old ones off and snapped new ones on.