MDB6650AWS Maytag Dishwasher - Instructions

Purchased a replacement lower rack WPL 99002572 (which had the wheels but not sure that it still does.) Used the old fold down shelf but this might be available as a part. The rack didn't have the tines near the rear of the rack on either side--my old one had fixed/welded tines so I didn't expect this and needed replacement parts to fix it. I Ordered 4 straight clips AP4112831 (99001436)CLIP, FOLD AWAY TINE to hold the tines. There weren't any recommended tines, so found and Ordered 2 each Front place and Rear Bowl tines WPL 12002218 x 2 and WPL 99002138 x 2 that looked about the right length. Used them in pairs. On one side of the rack (right side), only the bowl configuration works--this is because the tines catch on the edge of the basket and won't fold straight up. On the other side (left), I can switch between bowl or straight tines by folding them different ways. To make this work,clip the tines to the basket so the tines set a little closer to the center of the basket than you might expect, in order to allow the tines to 'float' enough to rotate to the opposite configuration. I had to experiment with the clip location so needed a needle nose pliers to gently unlatch the clips so that I didn't break them. I also ordered a clip AP4113042 (99001746)Latch, pivoting tines--but didn't use them with these bowl tines. They might be useful with a straight tine for latching the top to the outside of the basket.

I pulled the unit out its bay and saw that one spring was missing. I looked up the parts online and ordered replacement springs and linkages. Using the existing spring and linkage as models, I easily installed the new parts. I ordered spare parts in case the other linkage broke.

They just snapped in to place. Once I realized where they went. They are not the exact rollers needed but will do until I get the right ones. The rack will not come out as far as it should because of the difference. Other than that....easy.

I removed the four screws that hold the front kick plates on. Then, I removed the hose clamp (on the right side of the pump that secures the top shower hose assembly to the pump assembly. Then I pulled the dishwasher out, and pulled out the four black snap clips that hold the insulation in place. I then folded the insulation back and reached inside the dishwasher to disconnect the hose assembly. On the top spray arm is a nut that is easily removed without any special tools.
Be sure to save the rubber washer unless you order a new one along with the top shower hose.
Overall, an easy fix. Saved about $100.00 by doing it myself.

Looked into the problem, cleaned the sprayers out to no avail. Looked at drawings of dishwasher and noticed it had a filter. That seemed to be the next easiest thing to check. Removed the lower spray arm with channel locks, then removed the filter housing by removing 6 screw, removed old filter, replaced with new and reversed the above steps for re-assembly.

Piece of cake!

da basket don't come with rections so you gota figer it out yor sef. I tride pullen the handle off and it work then I tride pushen it on the other basket and it work to. Then i tride swapen dem and it work so thats how ya doit

removed old and broken and replaced. The best part was, the turn around time from partselect. The fastest delivery of anything I ordered that part a 2 in the afternoon and had it the NEXT day, without specifiying any extra rush shipping. Right part too! Amazing job! Thanks

***BEFORE STARTING BE SURE TO TURN OFF THE POWER!!
THE SPRING TENSION WAS GONE THAT WOULD KEEP THE DOOR FROM FALLING. KEEP IN MIND THERE IS A DOOR SPRING AND LINKAGE ON BOTH SIDES OF THE DOOR. SO BUY 2 OF EACH AND RETURN THE ONES YOU DON'T USE. IF YOU REPLACE THE LINKAGE ON ONE SIDE YOU MIGHT AS WELL CHANGE THE OTHER ONE SINCE IT'S ONLY A SMALL PLASTIC PIECE.
FOR ME THE SPRING WAS GOOD - ONLY REPLACED THE LINKAGE. REMOVED THE PANEL AT THE BOTTOM AND THE 2 SCREWS THAT HELD IT UNDER THE COUNTER TOP. I DIDN'T DISCONNECT THE WATER BUT WAS ABLE TO PULL THE UNIT OUT JUST ENOUGH (10 INCHES OR SO) TO GET TO THE SPRING. HELD IT IN PLACE WITH THE VISE GRIP SO IT DIDN'T FALL BEHIND THE UNIT. FYI - YOU MIGHT HAVE TO ADJUST THE TENSIONER ON THE BOTTOM IF YOUR SPRING TOOK A WALK WHEN THE LINKAGE BROKE. BE CAREFUL PUSHING THE UNIT BACK UNDER THE COUNTER. TOOK ME ABOUT AN HOUR AND SAVED SOME MONEY

When the (overpriced) replacement silverware basket arrived (rapidly, within a few days of my ordering) I was shocked and angry that the handle for the basket was not included--nor were instructions included as to how to remove the old handle from the old basket in order to fasten it to the new basket. Therefore, I spent a considerable amount of time trying to pry the handle off the old one, which was quite tricky: There were four slots which held the plastic "catches", and they had to be pushed out simultaneously. I had to fiddle with it for at least a half hour, trying various implements, until I found that I could push them out simultaneously by wedging butter knives into the slots and then easing the handle off. (I was careful to position myself so that I wouldn't slip and stab myself with the blunt butter knife.) After that, the handle snapped fairly easily into the new basket's slots.
In the end, while I was glad to be able to recycle the old handle, I wish that the basket and shelves were made more durably so they wouldn't have to be replaced, or that they could be replaced at a more reasonable price.

When I tried to remove the hold down screw for the impellar, the impellar broke in half. I actually did npt need to go this far with disassembly as the problem was with water being retained in the rinse arm assembly and stagnating. This was due to calcium buildup clogging the drain holes. Clearing the holes resolved the problem.

Just slide the old upper dishrack forward to the end. The stops on either slide must be removed . Only difficulty was getting the plastic stops to open up. We used a thin metal knivre to wedge into the opening.

Removed 2 each screws from counter top. Pulled washer out 1'. Installed springs and linkage by hand with door closed. Push washer back reinstalled 2 screws.

Took off the lower front plastic piece and unscrewed the side panel to snap the new part in place then attached the spring to it.

Turned off the water. Disconnected the water supply line. Extracted 2 screws holding the dishwasher. Pulled out the dishwasher. Changed out the nylon spring link. Pushed the dishwasher back into place. Reattached the water line. Turned the water back on.

Spring linkage and postage about $15.00.
Savings on service call and parts about $175.00. What a deal. Thank you PartSelect.

Removed front access panel
Disconnected water supply
Pulled dishwasher out approximately 1 foot to gain access to spring linkage
Connected new spring linkage to spring, connected other end of spring linkage to door
Tested operation of door
Slid dishwasher back into place, reconnected water supply and front access panel