WC201 Maytag Dishwasher - Instructions

I replaced the belt and door spring. Now it works perfectly, and the door doesn't drop with a bang.

No problem at all. Belt slipped on very easily. Followed directions in the package.

Very easy,take off the old faucet screen and screw on the adapter. What I really liked was the ease of ordering the part. In less than 5 minutes I had located the part and ordered it. Less than 3 days later, I had the part. Way to go PartSelect.

Typically when the detergent is not being despensed during the wash cycle, the bi-metal switch is bad (they don't tend to last forever). I took the 4 lower screws out from the inside of the dishwasher door,, unscrewed the bi-metal switch, and screwed in the new switch. I also decided to replace the metal spring for the dish as well, which took the majority of the time. Once you get the idea of how that spring is wound in there, the install goes pretty quickly.

Took off bottom cover. Put belt on center housing than put belt on moter pully.Rolled belt down onto center pully while turning pully clockwise. Popped right on.

It was either the timer assembly of the Dispenser cup assembly. After looking at the dispenser critically< it appeared that the cam was quite worn. The replacement was accomplished by removing the bottom part of the door (4 screws) and then removing the dispenser cup (8 hex-head screws). If you keep the starter lever to "off" there is not power to the timer and you do not need to disconnect power

Removed four screws that hold front panel. Disconnected two wires, removed six screws, cleaned of old gasket material. Installed new gasket and soap dispenser with six screws. replaced two wires. replace front panel.

I opened the bottom part of the dishwasher, from there you can see all parts of the motor including the pulleys where the broken belt came from. From here, I took the new belt, placed some silicon all around it and installed it by rotating the pulleys clockwise until the belt wraps around it.
Then I tested it by turning the control on the Wash/Rinse mode and it started to drain the water right away.
DONE!

NO PROBLEM!!!

PS.
THANK YOU FOR DELIVERING IT ON TIME.

Turn off power, remove the lower kick plate and lower trim panel with the nutdriver. The float switch is in the front on the left. Remove the two wires on the switch. Use a #1 philips to remove the one screw holding the switch to the frame. Remove switch. Install wires on new switch and install switch using the screw. Be sure to get the plastic float arm under the switch. Raise float and observe the switch clicking on and off. Replace lower plates and restore power.

Remove lower cover, 4 Phillips screws. Remove bracket with float switch, two hex head screws in the rear. After removal pull switch wires, two in plastic housings. Remove float switch, one small Phillips head screw. Remove float switch lever, one Phillips head screw. Clean the bracket and lever. Replace the lever and lube with silicone. Replace the float switch, (new one) and replace wires. Reinstall install bracket with original hex head screws. Replace lower cover. Done.

replaced belt....great service!!

Removed front panel by removing four screws. Used 5/16 nut driver to remove six screws holding dispenser and disconnected two wires. Inserted new dispenser and reattached cover. Longest time taken was to realign cover properly. Best approach seemed to install with door as near vertical as possible and to start screws by hand. ONLY FOUR screws hold the panel in place. Very easy repair for anyone. part arrived sooner than expected.

removed screws that secured cover plates. discovered that belt was broken. ordered new belt. ordered friday; delivered monday. read some previous repair experiences.

the trick to getting belt onto the pulleys is to first wrap it around the spindle part. then set the belt into the motor pulley groove. carefully start working the belt in the other pulley into the groove while rotating both pulleys. i had to lay on my stomach on the floor to do this, but it did not take very long. once the belt is in place, lubricate it with the included gel. took about 20 minutes with some trial and error.

It is realatively simple to replace the dispenser cup. Revove the 4 screws on the inside edge of the door (Not the upper screws for the upper
control panel). The front cover will come away exposing the dispenser cup. Using a 1/4 nut driver
remove the 6 (I think) screws after unplugging the electrical connector. (Be sure & replace in the same position.) After removing the screws, the unit will easily come away. Clean the old gasket remnants & crud well and place the new gasket and cup in line with the nut holes.

Shut off the hot water supply (pretty sharp eh?). Disconnected the hose from the hw supply and the at the connection to the washing machine. These had not been touched in at least 15 years and were somewhat tough to loosen but finally came ..... accessibility was a problem for the connection to the water supply as it was in a recessed wall box. Fortunately, we had some washers for the hose connections so the install was a snap. Hardest part of the whole job was moving the washing machine out from between the drier and the wash tub .... tight fit. Thanks for the quick service and to FED EX for their delivery. The delivery fellow was a real gentleman.