Models > WU901 > Instructions

WU901 Maytag Dishwasher - Instructions

Jump to:

All Instructions for the WU901
91 - 101 of 101
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Robert from Bandon, OR
Parts Used:
WP99002560
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Dishwasher would pump the used water out.
Changed float switch to no avail! Ladeled out the water. Disassembled the entire pump unit inside down to the motor shaft and checked all pieces for trouble. Could find nothing wrong. Now trying to determine if the problem is in the timer or motor.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Noel from Temperance, MI
Parts Used:
WP901403
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
leaking water
replaced gasket.Didn't fix leaking water problem.I believed that there was too much water in washer, when the problem occurred.Found that the float had soap build up in it making it too heavy,letting in more water than the washer can handle.Cleaned build up from float and problem seems to have disappeared.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Roger from Saganaw, MI
Parts Used:
911594
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Nipple that upper spray arm goes on.
Maytag dealer said the part was unavailable but there I sat looking at it.
Was this instruction helpful to you?
Thank you for voting!
Customer:
walter from salisbury, NC
Parts Used:
WP99002560
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
water leak - tub overflow
remove panel on front to acess float @ float switch.Remove phillips screw to float switch,remove palnut from float shaft with 5/16 nutdriver.Remove float from inside washer.Reinstall new parts reverse order.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert B from Frederick, MD
Parts Used:
901111
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
stretched door springs
Locked door closed, removed lower access panels with 5/16" nut driver, removed old springs with needle nose pliers, put plastic piece on top curved end of spring and placed on slot in door bracket as shown on instructions with part. Did same thing for the other door spring, used the screw driver to stretch the springs down to the first hole in on the base of the dishwasher on each side. Replace the panels. Job done!
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Castro Valley, CA
Parts Used:
901298
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Wrench set
Very noisy stuttering when water came on
Had to reuse the original mounting bracket instead of the one that came with the replacement part (held on by 4 screws). Also had to turn each solenoid 90 degrees (a feature of the replacement part) so that I could reuse the original connecting wires. Dishwasher running very quietly now.
Was this instruction helpful to you?
Thank you for voting!
Customer:
WILLIAM from CONNEAUT, OH
Parts Used:
6-9021150
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Broken Belt
After discovering the broken belt. 2 Days later I had the new belt from partselect. I placed the belt on the motor pulley then after 3-4 attempts was able to get the belt on the other pulley. It will go on. Comments from other customers really helped. After you get belt on then apply lub, per instructions. My maytag is over 20 years old still works great.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Hugh from Avon, MN
Parts Used:
6-9021150
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
The dishwasher did not drain
"The order arrived in relatively short order. However, the installation must have been hilarious to any observer. Imagiine an arthritic septuagenerian getting down on the floor and wallowing about fitting a dish washer belt. Hints: 1. Grasp the pulley on the pump with your left hand from under the discharge hose (more room than over the hose) when fitting the belt to the rear of that pulley. 2. Use a hot pad (not an emroidered & quilted one reserved for company) to protect your L forearm from the frame member on the bottom of the machine. Getting up was worse than getting down, but it works! In dishwasher years it's much older than I am."
Was this instruction helpful to you?
Thank you for voting!
Customer:
JOHN from SLIDELL, LA
Parts Used:
WP901403
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
water leaking at door of dishwasher
based on instructions from previous customers, took off front control and door panel, removed old gasket, replaced new gasket by aligning tabs and pulling through with needle nose pliers, leaking stopped
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Slidell, LA
Parts Used:
6-9021150
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Motor running but no motion or pumping action
Removed the kick plates to access the pulley system, Heated the clear belt in hot water and installed it by rotating the large pulley to stretch the belt on. Then added the lubricant to the belt. Reinstalled the kick plates with nut driver.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Los Alamos, NM
Parts Used:
6-9021150
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Belt to stiff to roll onto pulley
150 degrees for ten minutes provided enough flexibility to allow the belt to be rolled around the pulley. The machine has been used successfully since installation.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WU901
91 - 101 of 101