WU202 Maytag Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from Slidell, LA
- Parts Used:
- 6-9021150
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Motor running but no motion or pumping action
Removed the kick plates to access the pulley system, Heated the clear belt in hot water and installed it by rotating the large pulley to stretch the belt on. Then added the lubricant to the belt. Reinstalled the kick plates with nut driver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILLIAM from CONNEAUT, OH
- Parts Used:
- 6-9021150
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Broken Belt
After discovering the broken belt. 2 Days later I had the new belt from partselect. I placed the belt on the motor pulley then after 3-4 attempts was able to get the belt on the other pulley. It will go on. Comments from other customers really helped. After you get belt on then apply lub, per instructions. My maytag is over 20 years old still works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- walter from salisbury, NC
- Parts Used:
- WP99002560
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
water leak - tub overflow
remove panel on front to acess float @ float switch.Remove phillips screw to float switch,remove palnut from float shaft with 5/16 nutdriver.Remove float from inside washer.Reinstall new parts reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Bandon, OR
- Parts Used:
- WP99002560
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dishwasher would pump the used water out.
Changed float switch to no avail! Ladeled out the water. Disassembled the entire pump unit inside down to the motor shaft and checked all pieces for trouble. Could find nothing wrong. Now trying to determine if the problem is in the timer or motor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Noel from Temperance, MI
- Parts Used:
- WP901403
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
leaking water
replaced gasket.Didn't fix leaking water problem.I believed that there was too much water in washer, when the problem occurred.Found that the float had soap build up in it making it too heavy,letting in more water than the washer can handle.Cleaned build up from float and problem seems to have disappeared.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Saganaw, MI
- Parts Used:
- 911594
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Nipple that upper spray arm goes on.
Maytag dealer said the part was unavailable but there I sat looking at it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert B from Frederick, MD
- Parts Used:
- 901111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
stretched door springs
Locked door closed, removed lower access panels with 5/16" nut driver, removed old springs with needle nose pliers, put plastic piece on top curved end of spring and placed on slot in door bracket as shown on instructions with part. Did same thing for the other door spring, used the screw driver to stretch the springs down to the first hole in on the base of the dishwasher on each side. Replace the panels. Job done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Lake City, MN
- Parts Used:
- 6-9021150
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
would not drain
The part was a bit difficult to put on and then I discovered that it still would not drain. It turned out that my drain hose was plugged
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirley from Brewer, ME
- Parts Used:
- 6-9021150
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Space too small to see just where to place belt - Plus the belt had to be put on at the bottom of the dishwasher.
My husband and I both tried to get belt around the pulleys according to directions that came with the belt. The space was just too small to work in. We ended up turning the dishwasher upside down! We could then see what we were doing....My husband finally got the belt on....He did end up with lots of small cuts of his hands from sharp edges. But we were so happy to get it fixed. We had priced new portables dishwashers at six and seven hundred dollars. We were thankful to be able to get the part for our 23 year old dishwasher. It is now working great.
Was this instruction helpful to you?
Thank you for voting!