DWU7300ABX Maytag Dishwasher - Instructions

I removed the inside door cover, unpluged the accuator, removed the two screws holding the dispenser latch in place. Replaced both the latch and rubber groumet. returned the door to normal operation and verified no leaks was present.

Removed door interior, confirmed with tester that power was reaching door cut-off switch, but not power on other side of switch when engaged. Noticed that little switch button frozen in shut position, assumed switch had burned out. Installer new door cut-off switch with new (dual) switch units in place, plugged in unit and it ran perfectly.

Basket Replacement very simple just remove old and set new basket in place

pulled out the old gasket, cleaned the area before pressing in the new gasket with my fingers ,I made sure to put it in the same way as the old one. You have no idea how happy I am that this solved the problem.

First I replaced the door gasket as every one else. This cut drips about 30%. I then discoverd that the Rinse Aid circular dispenser cap was opened about half way. I turned the cap tightly clockwise to close and cut drips to 90% total. I czn live with the other 10%,

Shut off the water and electric then removed the cover at the bottom then removed the water inlet valve and replaced it with the new one. Turned on water and electric. Replaced cover at bottom. Very easy and the part was shipped quickly. No problems and the dishwaser works great now!!

I simply looked at the other side (which was still functioning) and put the new one on but in reverse (left side/right side) I also was missing the end stop to the slide and simply popped that in and snapped closed. Two simple parts and 15 mins. solved a whole lot of aggrivation,
without any aggravation! wish I had found this site sooner!

Took out the old basket,
Threw it away.
Popped in the new baskey,
filled it with forks and spoons.
Works great!

By the way, my order arrived in one day.
Phenomenal!

just unscrew the inside panel. using a torx screw driver. disconect vericarefully the bad actuator and install a new one. put back everything in back order .

Ordered 3 parts first ..all came within two biz days..forgot the toe panel, called it was here the next day! The people that assisted me were wonderful! My husband did the repair. the dishwasher looks like new!!!!! I will order from Part Select again and again...extremley pleased. Now if only we could cover the Refrigerator in Black it would look like a whole new kitchen!

Had service man: stated I would need new motor/pump at $400 complete. I didn't like the interior of new dishwashers. Nothing to lose, so I verified that the motor was working; reviewed short PartSelect video. Ref: very helpful PartSelect assembly diagrams with parts list. THANKS PS! Removed two dish racks (top rack: extend fully and flip the roller-keeper clips. Pull rollers and rack-pins apart) Then I started taking the pump apart all the way down to the pump base (fits into tub with seal - did not replace that seal). Very intuitive - some parts are tight and must be encouraged to come apart; take care of seals and o-rings; take notes of sequence if necessary. Look for parts requiring replacement. Unscrew Spray Tower Lower Extension Nozzle and lift off Spray Arm and two lower spray arm seals - check seals for wear. Unscrew pencil-like Spray Arm Support Nut. Cause: I found a totally-clogged Pump Housing Filter, a bit of steel wool about the size of my thumb (same size as water supply opening in bottom), and small piece of broken glass. Cleaned all parts coated with lime; new Pump Housing Filter (could not clean adequately). Cleaned the screens underside of filter support (difficult) with brush and wire. Replaced o-rings for Wash Impeller and Drain Impeller as a matter of principle. Only alignment requirement is with bottom water supplly hole. Everything works like new now! Recommendation: clean Pump Housing Filter annually.

Removed dishwasher door liner and removed soap dish door latch assembly. Removed latch from assembly and replaced with new latch. Had trouble replacing assembly in correct sequence. Had to go on line and look at sequence picture to replace assembly correctly. Installed new gasket and replaced liner in door. The new gasket and latch solved my leak problem.
Thank you PartSelect

my husband took the bottom rack out, unscrewed it where there were screws, lifted up the unscrewed part, took the filter out,cleaned out any gunk, replaced the filter put the part back on, rescrewed it, put the rack back in and it works much better.

The dripping water was coming from bottom right side of the door, almost directly beneath the detergent dispenser. Looking closely at the drips, I could see that they were coming from saturated insulation that is between the inner and outer door layers. I took the inside piece of the door apart and sure enough I could see water had been getting through the door latch and running down the inside of the door. I could see that the grommet around the door latch was cracked and brittle, so I replaced it and was pretty sure that would resolve the problem. But when I put the door all back together and did a test run, I had a leak even bigger than the first, but this leak appeared to be through the door seal at the bottom right. I then ordered a new door seal, which took only 5 minutes to replace and resolved the leak. I think the old door seal was too worn out at that spot and just by removing and replacing the inside door layer, it must have not made a good seal at that point. But I recommend starting with the door latch and grommet first, since that is a $4 part, and then proceeding with the door seal, a $43 part, only if necessary.

Remove screws holding the inside of the door. Set lid aside. Pull out the old foam insulation. Clean the area. Replace with new foam insulation. Put door back together.