MDB5600AWW Maytag Dishwasher - Instructions

A common theme you'll see thoughout the repair stories;

1. many broken handles at the hinge
2. TURN THE POWER OFF.

This assembly comes with the microswitches (which is not a bad idea to replace since they are electromechanical and will eventually fail). My only recommendation is to buy a couple of these handle assemblies because they WILL fail. I'm on my 3rd!

Door gasket fit in like a champ! No special tools required - just scissors to trim off the excess ends. Unfortunately this didn't correct the leak. The leak was caused by a Home Inspector who ran the dishwasher without soap. The soap has a defoamer in it. If you run the dishwasher without soap the water mixes with the surfactant in the jet dry and causes foam which results in a door leak. The foam also causes the pump to cavitate which is not healthy for the pump.

Followed the suggestions on PartSelect - took off the screws on the door; removed 2 screws on the assembly that held it to the door; disconnected switches (hardest part) - they seem to fuse on(or rust) from the moisture; took the new (much sturdier part than original) assembly and plugged in the switches; set in place; replaced the 2 screws, replaced the screws holding the door panel - Complete - works great! Here we thought we would have to get a new dishwasher!!!!

Removed 11 T20 Torx head screws. Removed and replaced latch. Removed and replaced door seal and foam insulation strip - no additional tools required. Super easy to repair and didn't leak a drop afterwards.

I would not have figured it out had I not viewed the video on installing the latch assembly. The latch must be in the LOCK POSITION before installing. It would help if the latch was in the LOCKED position before shipment.

Shut off power to dishwasher, remove screws holding panel to door , move panel enough to get to circuit board. Remove three nut drivers screws, unplug cables from circuit board. Remove circuit board by unsnapping from side ears, replace new circuit board, plug in cables. secure with screws, secure door panel. put power back to dishwasher.

I first listened carefully and noticed that during cycling, the electric motors could be heard starting, stopping, and apparently running normally during both wash and emptying cycles. However, no water was being pumped around during the wash cycles, while emptying (which uses a different motor) worked normally throughout all cycles. Thus it seemed to me that the electronic programming was working correctly in turning both motors on and off as necessary. So I figured somehow the wash motor impella was not turning and pumping water, despite the fact that the motor was indeed running correctly. So I removed all the plastic housings, the screwed on impella, and the metal chopper at the base of dishwasher. Then I was able to easily pry the old plastic chopper sleeve right off of the electric motor shaft (normally it is screwed on and cannot be pryed off). Since the plastic threads inside the chopper sleeve were completely stripped, the motor shaft would turn but the impella would slip on the shaft and not be driven. The replacement sleeve was much better constructed (metal not plastic). It could be easily screwed on to the motor's driveshaft after lifting the old rubber seal and gently holding the motor shaft with a pliers (carefull to avoid scratching the shaft). I removed the old rubber seal nd replaced it with the new one from the kit, right over the newly installed metal chopper sleeve. Next, I easily centered the metal chopper sleeve and pressed in the new seal after reinstalling the plastic/metal chopper screen, using the temporary jig included in the kit. Then the jig was discarded and the impella simply screwed onto the chopper sleeve (using the appropriately threaded hold-down screw provided in the kit). Finally, the rest of the plastic hardware is screwed in place. Waahhlaa...now impella is motor driven again and blows water hard into the dishwasher during the wash and rinse cycles. Total cost of job to do-it-yourself, $29.50 including shipping (which only took three working days). Estimated job if down by appliance repairman, $140 (assuming the repairman didn't first erroneously blame the problem on faulty electronics then charge you hundreds of $$'s to replace circuits which were not broken to begin with, only to find the dishwasher still not washing/rinsing after his expensive electronic circuit replacements. The actually mechanical fix was cheap and simple. Truthfully, there is no excuse for Jenn Aire to ever use a plastic Chopper Sleeve in their dishwashers to begin with.......carefully planned obsolesence if you ask me. Oh well, it works perfect now. I doubt if even the four marbles my 4 year old had tried earlier to wash in my dishwasher (stripping out the original chopper sleeve) would do any damage to the metal replacement. However, I don't plan on testing my hunch. A simple fix, but a slightly challenging diagnosis which relied on a keen sense of hearing and a quiet workplace. Seems many people in these blogs have had the very same problem with their Jenn Air/Maytag dishwashers, and have made the same diagnosis and the same simple fix. Thank you mucho, PartSelect.

Unplug the power cable. Remove 11 torx fasteners holding the inner door panel. Remove two sets of wires from old opener and install the new door opener assembly. Replace all the screws. About 10 minutes with a power driver.

Removed the bottom tray. Removed the two clips in the top tray guides and removed the top tray. Removed the top spray arm and transfer tube by unclipping it from the top and at the back and then rotated it down and out. Removed the six screws around the upper pump housing and removed it along with the bottom spray arm. Removed the three screws holding the filter protector plate and removed it. Removed the two screws holding the accumulator / flow plate and removed it. Put it back together in reverse order careful to not over tighten the screws.

I originally ordered the incorrect piece via the website, however when calling PartSelect to return the part they informed me that they could help me find the correct piece which they did. The correct piece arrived within 4 days. It was easy to install. The part works well. I'm very happy with the customer service.

Remove inside cover and eight screws. Unplug two electrical connections.

Pulled out the dishwasher, disconnected the electrical, water, and waste lines.Then removed 2 screws that held the valve in place, and the supply line. Swapped out the new valve for the old one, replaced dishwasher, reinstalled the water, electrical, and waste line. Turned the water valve on, checked for leaks, and fired the old dishwasher up.

Switch was not the same switch as what was in the unit, similar but switch was normally closed instead of open, so had to take the switch apart and change sides with the contacts! should be the same, but was not, so in the end worked fine after an adjustment!

1.Disconnected the electricty 2. pulled the dishwasher from under the cabinet 3. tilted the washer on it's face (water supply was long enough and did not need to disconnected.)4. unscrerwed the 2 plastic nuts that hold the heating eliment in place. 5. tilted the dishwasher back upright and removed the old heating element. 6.put the new part in place had a helper tilt the washer forward while i tightened up the two plastic nuts to hold the part in place.7 reattached the elecrtic conectors to the heating element. 8. pushed the dishwasher back in place. 9 hook the electricity back up. During step 4 i had to remove the electric connectors from the old heating element.

I remove the inner door panel, disconnected two quick release connectors, unscrewed the old part from the inner panel and installed the new one.

The new part arrived quickly and was the perfect match.