MDB8751BWB Maytag Dishwasher - Instructions

The original piece is 100% plastic (with metal shields only to prevent burning). The bushing of the arm was badly worn out in one side. The arm was no turning properly or at the end no turning at all. I decide to drill the new part in order to fit a brass bushing inside (1/4" ID, 5/16" OD, about 2" long). I expect it will last considerable longer. I would say this is a typical "defective by design" problem.

from inside the door remove torx screws down each side and top , pull panel back , removed 6 screws from back of dispenser ,unplug 1 wire connection ,reverse procedure , real easy repair.

Unfortunately, my experience was unlike that of the other people who posted. While everything did go back together it was very difficult to get it all to press down tightly enough to tighten each set of screws. The project took about 2.5 hrs and I still don't think it is exactly right. I'm still going to have a professional out to finish the job. Also, the tool needed to complete the job was nothing fancy, but also not in everyone's home tool kit.

Snapped the old part out and snapped the new part in.
It was a piece of cake.

Turn off the DW power (pull the fuse or turn off the circuit breaker) Open the dishwasher door. Remove the torx screws around the periphery of the door inner panel. Lift up the inner panel far enough to get at the door latch. Lift out the entire door latch assembly. There are two wiring connectors attached to microswitches on the latch assemby. Remove the connectors. The connectors were pretty tight, so I needed pliers to pull the connectors off the switches. Discard the old latch. Get the new latch, and plug in the connectors (keep track of which wires go on which side). Lay the latch down in the door so it lines up with the mounting holes. Lay the cover back down, start each of the torx screws into their threaded holes, then tighten them all. Don't over tighten. Turn power back on. Job done. It almost takes as long to type it up as it does to make the repair.

I thought the door springs were broken so I ordered both springs and cables. After the parts arrived I removed the six screws that hold the dishwasher in place and slid the dishwasher out about five inches. Neither of the springs were broken but one of the cables was broken. I changed both cables, slid the dishwasher back in place and replaced the screws. The whole job took about 20 minutes. It was a very easy job.

I was extreemly pleased with the replacement handle unit. The original unit had a plastic pivot points - the replacement part replaced these points with metal rods. The pivot points on the old unit were the points of failure.

The repair should have been done with a "star" head. Not having this, I was able to use a hex wrench instead.

The repair time was less than 10 minutes, most of that time removing and replacing the star head screws. If you have removed the old part, you have essentially completed the repair.

The biggest problem was identifying the proper handle unit. There are two very similar. Measure the distance between the mount holes in the unit and refer to the grid in the picture. The grid on your site was extreemly helpfull given the lack of part numbers printed on the Maytag OEM parts.

I unscrewed the inner door panel and the old latch assembly came out. I went to the circuit breaker and cut off power to the DW. Then I unplugged the old latch assembly and plugged the new one in. There were some springy metal pieces that had to be pushed back to get the old plug off and the new one on. After that it was just a matter of aligning the holes of the latch assembly with the holes for the screws and replacing all the screw holding the door panel, and tightening them up.

First, I removed the screw, then I took off the old wash arm, then I replaced the wash arm, and replaced the screw. Nothing could be easier!

I followed the you tube video exactly. Very easy to do. I did not tighten the screws sequentially as shown in the video, rather I did the opposite ones to make sure nothing was skewed. Very easy, about 20 minutes.

Repair was fairly easy. There are 11 screws You have to remove then simply unplug the electrical connection from the door latch/switch and plug in the new one line up the screw holes tighten them down and your in business.

FIrst I went to your web site; located the part on the easy to read diagram. Next I ordered the part. When the part came to the house (2-3 days), I opened the box and then the packaging, I screwed the part in and Wala! Boom! Bang! She was fixed!

All kidding aside. The part order was quick to locate, quick to ship and one of the easiest companies to deal with. I will return on my next dyi project.

My married daughter actually did the repair. I removed the plastic assemblies that held the upper cage and upper spray assembly. She unscrewed the screws that held the filter/impeller assembly in place and replaced the old one with the new one. I finished the job by cleaning the interior of the washer and putting everything back together. The dishes are sparkling clean again!

First I removed the torx screws halding the inner door panel on. I then seperated the door panel from the door and removed the latch assembly and disconnected the switches from the latch. After installing the switches on the new latch I replaced it between door and inner panel. Finally I replaced the torx screws and was finished.

I pulled the AC to the device, took the door apart , unscrewed the mounting to the door, unplugged the wires to it, plugged the wires on the new part, screwed it to the door, and finally put the door back together. Oh yeah, had to plug AC back in.