DWC7400AAW Maytag Dishwasher - Instructions

Removed covers on the bottom of dishwasher so I could get access to area. Measured no voltage on water inlet pump. removed to wires from foat switch, one screw to remove float switch. When I pressed the float switch button to activate the switch would not move. Ordered and replaced the switch. 30 minutes tops

I removed lower cover panel. Removed two wires. (one on each end of the element. Removed two nuts on the element. Took out old part. Put new part in and reversed procedure. Works fine now.

First I replaced the soap door grommet -- door still leaked. Then I went for the really expensive part ($40) -- the door gasket. The old one came right out and the new one went right in -- 15 minutes tops -- and the door no longer leaked.

Thanks to all the previous posters for their hints.

My husband does all the repair work himself so he tore it all apart but it's hard to find parts for a 23 year old machine. A store about an hour from our house said they had the part. When we got there it was the wrong impeller and it was going to be $30 to order it in. I got home on that Weds. nite ordered it and had the part 2 days later on that Friday.My husband had the part in and the dishwasher running within 20 minutes. Thrilled with the fast service from you and my husband :)

easy repair. The foam has to go over some wires but if you stretch it alittle as you place it all goes well

I removed the screws holding on the interior door panel. This exposed the soap dispenser latch mechanism. After removing the two retaining screws I transferred the original parts to the new retainer and replaced the grommet prior to reinstallation of the mechanism and interior door panel. A savings of probably $100.00 or more for a service call and parts. Should last a few more years.

I recieved a different part than was in the picture and description that I ordered, and was billed twice for it. I wasn't able to fix my dishwasher

received new basket without a basket handle; had to remove handle from old basket & attach it to new basket; took 2 separate tries to remove old handle & each try took about an hour; used screwdriver & pliers but had to be careful not to break handle; eventually used dimes to pry open & hold the attached sections of the handle open in order to free the handle from the old basket; we sure hope the new basket lasts a lot longer than the 2 years that the old basket lasted before it broke.

Remove the lower panel by taking out the 2 screws on top and 2 at the bottom of the panel. To diagnose the problem, verify that there is water supplied from the valve under the sink to the water supply valve under the DW. This can be done by turning off the valve under the sink, disconnecting the copper supply line under the DW then turning on the valve under the sink to see if water passes through the line.

The float switch is located on the left front (as you face the DW). This is activated by the float in the tub. Check to be certain that the float is not restricted. The contact point on the switch is a spring loaded plunger. It should depress as the float rises and pop back out as the float returns to its low point.

Turn off the circuit breaker for the DW. To remove the switch, pull off the two electric leads from the switch. Mark the top lead with a piece of tape. Then remove the one philips screw. Replace the switch by reversing the procedure. Note that you have aligned the float contact point with the float.

Removed 7 Torx Screws ... removed inner door panel ... snapped off the selinoid after noting the exact original position ... removed the Latch assembly 2 hex head screws ... removed the old Grommet which was crumbling apart ... stretched the new grommet in place. Then did the steps in reverse to complete a successful repair.
Thanks to your website, quick turn-around service and customer's repair stories, I probably saved a few dollars but mostly, I realized how much I love my dishwasher now more than ever!

The repair was very easy. The door gasket was a little short, but I gently streched it to the proper length. I replaced the other parts as a precaution as some others said they were really the source of the original leak. It went very smoothy and NO MORE LEAKS.

Attempted repair was quick & simple. Removed 7 torx screws, and then pulled the wax motor out of its holder. Pulled 2 wires off, and replaced old motor with new motor. Reattached wires, & reassembled.
Only problem was this did not fix the problem, so back to square one, but worth a shot.

Unscrewed bottom panel. I could see right spring in proper position, left spring lying on floor, and broken linkage. Ordered part from partselect.com. To install, had to unscrew dishwasher attachment to counter, loosen leveling legs, pull it out a bit, then could replace linkage and reattach spring, retighten leveling legs, then push back in and replace screws and bottom panel.

The dishwasher was running perfectly, but over time it leaked more and more. We were ready to throw it out, when I searched the internet and saw stories about a tiny gasket commonly failing. I couldn't believe that could be the trouble, but ordered the $3.75 part. Unscrewed the door, slipped out the old gasket and slipped on the new one. Screwed the door back. And the result? THE LEAK IS FIXED! Unbelievable. The old gasket had gotten stiff, probably exposure to soap, and it wasn't sealing properly. That $3.75 part saved us hundreds and hundreds of dollars and will give us extra years of use from our dishwasher.

1. Remove broken part
2. Put new part in its place ...it just snaps in.
3.Smile...it fit, it's done.