MDB7130AWS Maytag Dishwasher - Instructions

Removed four screws on bottom plate. Located repair site on outside of cabinet. Had to hook spring on bottom rear plate by brail. Then attached linkage to spring and ran stiff wire through linkage to raise it above arm. Called a man with stronger but larger hands had him stretch the spring while I guided linkage over arm and into the slot using the wire. Removed stiff wire with needle nose pliers and reassembled front plate.

Took off the float, the jam nut was hard to get off, we ended up breaking the bottom piece of the float to get it off, but that was okay because we had a new float. The new float went on real easy and the jam nut went back on real easy. The foam insulation strip was real easy to get off we got a good hold of one end and striped it off slowly so there was nothing left on the door, then we cleaned the surface and put on the new insulation strip. We ran dishwasher to test it and there was no leak. Awesome. Cheap and easy to repair. We were impressed.

I aligned the V-shaped tabs on the inner side of the part with the slots in the mating part and simply pulled the old part out (it was already disengaged from the wheels in the metal rail). I then inserted the new part into the slots. One side went in well, but the other side required the part to be bowed slightly to match up the V-shaped tab with the slot. Then the hard part was getting the wheels in position to snap them on. Once in position, it took a bit of effort to engage the snaps in each wheel. I was afraid of breaking the new part. These snaps are very stiff and even with the notch between them there isn't any give, but I was able to apply enough constant, steady pressure to finally get them to snap in without breaking.

threw out the broken and put in a fantastically improved new one. very easy (would have done it sooner if I'd known it was that simple to find it online and order it) thanks

removed inner door panel. tested ythe Wax motor that operates the soap dispenser latch. It tested OK so I removed dispenser assembly. replaced the worn plastic parts and reinstalled the inner door panel.

slid the part in the groove (left side)

I took apart the lower spray arm apart and removed the 6 hex screws. I noticed that the little plastic circle thing had been ripped off the dome-shaped thing. I replaced the part and put it all back together.

It was difficult to use the guide provided online to determine what position to place the spring in. Finally I realized that the spring had to be placed with the tip that sticks out against the wall of the dishwasher to make the spring action work. The long and short pins were not a problem. How to place the spring was the main problem, but I finally figured it out. I did not need any special tools to accomplish this. I just used a kitchen knife to push the short pin into place.

Remove bottom rack. Unscrew the retaining ring on the wash arm, remove along with wash nozzle. Unscrew the eight retaining screws on the filter cover and remove (be carefull not to lose the two plastic bushings). Pick off and set aside the wash fan. Remove the six retaining bolts on the discharge housing. Pull up and remove the discharge housing. Remove the gasket (buy a new one, cheap and easier) with small screwdriver. Push gasket into new assembly. Under plastic nut with pliers and take off the plastic bushing that the wash arm rides on. Install new housing assembly with the parts that was taken off in the reverse order. Be carfull when installing the filter cover to make sure the drain outlet is aligned or mated to drain. Gently push down until the filter in down and continue reassembly.


(PS: Never use Sears parts, they extrembly slow as well unable to deliver on time).
Wash your dishes

Myscanning other reviews i saw mention dishwahser developed a small leak on RHS of door. I assumed the door gasket and planned to order that. On of the dispenser gromet which is only a $5 part so ordered that as well. I first replaced the door gasket which is an easy 10 mins job and ran the dishwasher again, but it still leaked.

I then removed the 7 torx screws on the door panel which came away easily. It was obvious that water was in there, so i removed the two screw on the dispenser with a nutdriver to replace the grommet. This process took 20-30 mins. After reassembly the leak was gone.

Without the comments on the website i would never have thought of the disepenser as source of the problem.

Open the soap dispenser door. On the top right side, there is a round pin holder. Take a small brad or nail and knock the pin out from right to left. Hold the door in place and after the right side pin is out, carefully slide the door up and to the right in order to remove the pin and spring from the left side slot. Notice how the spring is inserted in the slot as it has to go back in exactly as it came out. (short end first. Long end last.)

Put the spring on the left side pin and reinsert the door into place and then tap in he right side pin.

You're done but you won't know that until you run the dishwasher and if the dispenser door is open
at the end of the wash cycle, you did good. If not you have to reinsert the spring properly or buy a new spring if you've damaged the old one.

Good luck.,

RBM

Took out the pins that hold the detergent cup on, beginning with the side without the spring. Make sure you check how the side with the spring is installed before you take it out. If it's not done right when you put the new one on the lid won't spring open. Then installed the new detergent cup lid. Easy as pie and it would have cost $50 to just have someone come out to look at it and this cost $12. Can't beat that!

Was extremely easy to remove that existing rackings(upper and lower), install the new racks and snap in the new spray tower. It now looks like we have a new dishwasher. We are hoping that it will last another 10+ years.
We will recommend your site to friends.

Replacing my dishwasher racks was very easy. I followed the guidance on the PartsSelect.com website for replacing the upper rack. Replacing the lower rack was only challenging when I couldn't figure out how to remove the water sprayer from the old rack and place it in the new rack. A quick search on Google.com and I learned to turn the sprayer counter-clockwise to remove it and then clockwise to put it in the new rack. Worked like a charm! I would recommend PartsSelect.com to anyone. Easy to use, parts came quickly, and I appreciated the guidance from others.

I used a torx driver to remove the seven screws holding the inside door panel in place. Flipping it over exposed the dispenser mechanism. There were two hex nut screws holding the whole assembly in place and two wires attached to the wax motor. As an afterthought I had ordered the sealing grommet for the latch, and as it turned out, the main problem with the sticking latch was that the grommet had worn out and allowed the hard soapy water to leak into the slider assembly and build up a hard crusty residue that had helped to ware out the old wax motor. After completely disassembling all of the parts, I scrubbed the residue out of the housing, replaced the slider, latch, spring, and grommet. Next I snapped the new wax motor into place and connected the two wires. The whole thing went back in place and the two hex screws went back to hold it all together. Finally, the seven torx screws went back to put the door back together. The whole repair went without a hitch.