CDB3100AWX Magic Chef Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carrie from Platteville, CO
- Parts Used:
- 902882
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
our dishwasher needed a motor shaft seal
I recieved a different part than was in the picture and description that I ordered, and was billed twice for it. I wasn't able to fix my dishwasher
Was this instruction helpful to you?
Thank you for voting!
Both racks were rusted
Both racks are just roll out & roll new racks back in, no tools. Racks came in just 2 days, one was damaged in transit. Called to advise PartSelect of the problem. replacement rack was here within 2 days.
Great service. Jack
Great service. Jack
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clifford from Palm Harbor, FL
- Parts Used:
- WP99002560
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Dishwasher would not fill with water
Remove the lower panel by taking out the 2 screws on top and 2 at the bottom of the panel. To diagnose the problem, verify that there is water supplied from the valve under the sink to the water supply valve under the DW. This can be done by turning off the valve under the sink, disconnecting the copper supply line under the DW then turning on the valve under the sink to see if water passes through the line.
The float switch is located on the left front (as you face the DW). This is activated by the float in the tub. Check to be certain that the float is not restricted. The contact point on the switch is a spring loaded plunger. It should depress as the float rises and pop back out as the float returns to its low point.
Turn off the circuit breaker for the DW. To remove the switch, pull off the two electric leads from the switch. Mark the top lead with a piece of tape. Then remove the one philips screw. Replace the switch by reversing the procedure. Note that you have aligned the float contact point with the float.
The float switch is located on the left front (as you face the DW). This is activated by the float in the tub. Check to be certain that the float is not restricted. The contact point on the switch is a spring loaded plunger. It should depress as the float rises and pop back out as the float returns to its low point.
Turn off the circuit breaker for the DW. To remove the switch, pull off the two electric leads from the switch. Mark the top lead with a piece of tape. Then remove the one philips screw. Replace the switch by reversing the procedure. Note that you have aligned the float contact point with the float.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brad from York, ME
- Parts Used:
- WP902899
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dispenser door would not open
Attempted repair was quick & simple. Removed 7 torx screws, and then pulled the wax motor out of its holder. Pulled 2 wires off, and replaced old motor with new motor. Reattached wires, & reassembled.
Only problem was this did not fix the problem, so back to square one, but worth a shot.
Only problem was this did not fix the problem, so back to square one, but worth a shot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from Costa Mesa, CA
- Parts Used:
- WP99001576
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Silverware basket falling apart
Ordered new part from your site. The new basket arrived in just a few days, without the handle and cover for the small item section. Instructions with with new basket described how to remove the other parts from the old basket and install them on the new one. Everything worked out perfectly and my silverware stays put. I've very happy!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Philadelphia, PA
- Parts Used:
- WP912653
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dishwasher door was slamming down, heavy to close
Unscrewed bottom panel. I could see right spring in proper position, left spring lying on floor, and broken linkage. Ordered part from partselect.com. To install, had to unscrew dishwasher attachment to counter, loosen leveling legs, pull it out a bit, then could replace linkage and reattach spring, retighten leveling legs, then push back in and replace screws and bottom panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from ROCHESTER, MA
- Parts Used:
- WPW10117748
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
leaking door
easy repair. The foam has to go over some wires but if you stretch it alittle as you place it all goes well
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jerry from wilton, CT
- Parts Used:
- WP902894
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Door leaked from lower right corner
First I replaced the soap door grommet -- door still leaked. Then I went for the really expensive part ($40) -- the door gasket. The old one came right out and the new one went right in -- 15 minutes tops -- and the door no longer leaked.
Thanks to all the previous posters for their hints.
Thanks to all the previous posters for their hints.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Laingsburg, MI
- Parts Used:
- WP99002560
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No water would enter in dishwasher
Removed covers on the bottom of dishwasher so I could get access to area. Measured no voltage on water inlet pump. removed to wires from foat switch, one screw to remove float switch. When I pressed the float switch button to activate the switch would not move. Ordered and replaced the switch. 30 minutes tops
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marc from GLENDALE, NY
- Parts Used:
- WP99002560
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
After 22 years of virtually trouble -free service, I could tell by the sound that something was wrong. Water fill ran too long. Float not stuck. Checked and found float switch stuck.
Very simple. Remove bottom panels. Remove one screw holding old switch in place. Move wire connections from old switch to new one. Cleaned and lubed the switch actuator. Mounted new switch. Checked that float and actuator worked freely. Left bottom panels off till I ran a load - just to be sure all was OK. Remount bottom panels...Done! P.S. Don't forget to turn power off to dishwasher any time you work on it!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from FENTON, MI
- Parts Used:
- W10139223
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lower rack rusted through all over
Took rack out of box, son removed water tower from old rack, put it on new rack, rolled new rack into dishwasher. Presto! Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from Terre Haute, IN
- Parts Used:
- WP902894
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My dishwasher was leaking from the bottom right hand corner.
I removed the original gasket, wiped down the area, and installed the new gasket the same way the old one was installed. It was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from CHEEKTOWAGA, NY
- Parts Used:
- WP902894
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
When I would run my dishwasher, water would pool on the right side front of the washer. It was even dripping down into the basement. When I figured out it might be the the front door gasket, I ordered the part.
The repair was very easy! I simply pulled out the old gasket from around the front part of the dishwasher. I cleaned the area with a damp rag from any residue that was left on. I bent the long gasket in half and and pushed it in starting at the center of the dishwasher and went down one side at a time until the whole gasket was in. I then ran a short cycle on the dishwasher to make sure it was properly in place and the problem was fixed. NO MORE WATER ON THE FLOOR! I was so very happy to know my problem was fixed and I didn't need to buy a new dishwasher! It's been running great! :) ~ Elizabeth ~
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from goffstown, NH
- Parts Used:
- WP902894
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
washing machine leaked at right lower corner
removed old deteriorated gasket - just pulled out
cleaned soap particles from door seal area
pressd in new gasket - note orientation
done.
still leaks - will investigate further
cleaned soap particles from door seal area
pressd in new gasket - note orientation
done.
still leaks - will investigate further
Was this instruction helpful to you?
Thank you for voting!
The racks were very rusted and falling apart.
Just undid the brackets holding the top rack in place and put in the new racks, locked the brackets and in the bottom put the water tower on and slid that rack in place, and bam we were ready to turn it on. It's wonderful, all new and clean. LOVE IT!!!
Was this instruction helpful to you?
Thank you for voting!