OEMM1-DU2JV Magic Chef Dishwasher - Instructions

I pulled out the old gasket and put in the new one. You need to stretch it a bit as you guide it in the track.
It was very easy but did not solve the problem.
Apparently, Maytag dishwashers are known for a leaky soap dish which I figured out after the door gasket was replaced. The problem is usually with the soap dish latch. You need to take the inner door off, disassemble the soap diehs, out a new gasket and latch on, reassemble, and you should be all set.

Remove screws holding the inside of the door. Set lid aside. Pull out the old foam insulation. Clean the area. Replace with new foam insulation. Put door back together.

Ordered 3 parts first ..all came within two biz days..forgot the toe panel, called it was here the next day! The people that assisted me were wonderful! My husband did the repair. the dishwasher looks like new!!!!! I will order from Part Select again and again...extremley pleased. Now if only we could cover the Refrigerator in Black it would look like a whole new kitchen!

I tried tightening the latch (this had worked once before), but it was already tightened as far as it would go, and door still leaked. So I suspected the gasket, because the old one looked like it had lost its elasticity and was caked with crud. I tried cleaning it in place, but it still leaked. So I ordered a new gasket. However, it was back-ordered, so I tried removing the old gasket and cleaning it. It came out very easliy ( I had expected it to fall apart). Then I cleaned it good under running water, kneading the crud out of it. I also cleaned ou the groove, then I replaced it and that fixed the leak. So I didn't need the new gasket.

advisor showed a 30% chance that the part in question would solve my problem and it did. Had help from my 12 year old so it was a great teaching moment. She particularly liked when I forgot a part in final installation and she had to remind me to install before closing up the repair. 15 minutes total. Awesome fun!

ordered new gasket, watched the video that was in the order conformation on how to install which was very easy to understand. the actual installation was right on the money. Thank-you.

Unscrewed the 2 screws securing the dishwasher to the counter. Unscrewed 2 front panels. Shut off water valve. Disconnected water intake. Pulled dishwasher out 5 inches. Removed broken spring, replaced it. Checked the door movement. Scrubbed the door rubber gasket of calcium deposits & debris. Replaced the Teflon tape on the water intake. Reconnected water hose. Opened water valve. Checked for leaks at the water intake location. Ran 1 dishwasher cycle again for leaks. Pushed the dishwasher back under the counter. Secured the 2 screws on top of the dishwasher to the counter. Reattached the 2 front panels and enjoyed a glass of wine.

Access to the soap dispenser is easy just screws. One of the two hex head screws that hold the mechanism assembly is buried by a lever and required a with a special offset wrench, I used bent needle nosed pliers to loosen and remove the screw quarter turn at a time. The blocking lever was a snap-in and maybe could have been removed with high force, not generally recommended for 14 year old plastic parts. In hindsight I would use a digital camera to record the mechanism, due to a absence of any detail cartoons of the assembly. The lever arm load spring required tweezers to remove and re-install.

I disconnected the dish washer and pulled it out. I laid it on its back, unplugged the electrical wires,removed the electrical magnet and pried the shaft seal out with a flat screwdriver. I gently packed the new seal into place with the flat screwdriver. I connected the electrical magnet and wires. I then installed the dish washer and ran it through a cycle. I am pleased to say the dish washer does not leak now.

***BEFORE STARTING BE SURE TO TURN OFF THE POWER!!
THE SPRING TENSION WAS GONE THAT WOULD KEEP THE DOOR FROM FALLING. KEEP IN MIND THERE IS A DOOR SPRING AND LINKAGE ON BOTH SIDES OF THE DOOR. SO BUY 2 OF EACH AND RETURN THE ONES YOU DON'T USE. IF YOU REPLACE THE LINKAGE ON ONE SIDE YOU MIGHT AS WELL CHANGE THE OTHER ONE SINCE IT'S ONLY A SMALL PLASTIC PIECE.
FOR ME THE SPRING WAS GOOD - ONLY REPLACED THE LINKAGE. REMOVED THE PANEL AT THE BOTTOM AND THE 2 SCREWS THAT HELD IT UNDER THE COUNTER TOP. I DIDN'T DISCONNECT THE WATER BUT WAS ABLE TO PULL THE UNIT OUT JUST ENOUGH (10 INCHES OR SO) TO GET TO THE SPRING. HELD IT IN PLACE WITH THE VISE GRIP SO IT DIDN'T FALL BEHIND THE UNIT. FYI - YOU MIGHT HAVE TO ADJUST THE TENSIONER ON THE BOTTOM IF YOUR SPRING TOOK A WALK WHEN THE LINKAGE BROKE. BE CAREFUL PUSHING THE UNIT BACK UNDER THE COUNTER. TOOK ME ABOUT AN HOUR AND SAVED SOME MONEY

Actually following the online video is the way to go.

Use Screw driver to open the dishwasher door cover, you will see the Detergent Dispenser. I just took pictures before I remove any parts including the wires in case I forget where to put them back.

Video on website made the repair easy

Remove lower cover, 4 Phillips screws. Remove bracket with float switch, two hex head screws in the rear. After removal pull switch wires, two in plastic housings. Remove float switch, one small Phillips head screw. Remove float switch lever, one Phillips head screw. Clean the bracket and lever. Replace the lever and lube with silicone. Replace the float switch, (new one) and replace wires. Reinstall install bracket with original hex head screws. Replace lower cover. Done.

The time to hook up the spring was a minute or two. I simply attached the linkage to the door and then attached the spring to the linkage.The extra time in the repair was re-attaching the cover.