OEMM1-DU2J-CAN Magic Chef Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Tjhe nylon piece that attaches the spring to the door broke.
Attaching the part to the door only took a few minutes but getting the dishwasher out over the hardwood floor that was installed after the appliance was put in was a pain. I had to remove a piece of the hardwood floor and use some technique to get it out of the opening so that the springs were visable. There is no problem after that. I would recommend using work gloves to stretch the spring over the retaining notch on the door so that you don't pinch your hand.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Windsor, CO
- Parts Used:
- WP6-904027, 912529
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set, Wrench set
A leak around the motor shaft.
Everything is straight forward with the following two exceptions; The threads that hold the motor fan to the impeller are left hand, and it takes a special tool to remove the top rotating assembly. It took about 4 hours to figure out what to do, and make the tool . I put it back together in about 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Philadelphia, PA
- Parts Used:
- WP912653
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dishwasher door was slamming down, heavy to close
Unscrewed bottom panel. I could see right spring in proper position, left spring lying on floor, and broken linkage. Ordered part from partselect.com. To install, had to unscrew dishwasher attachment to counter, loosen leveling legs, pull it out a bit, then could replace linkage and reattach spring, retighten leveling legs, then push back in and replace screws and bottom panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from West Union, OH
- Parts Used:
- 903096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dishwater cold
I removed lower cover panel. Removed two wires. (one on each end of the element. Removed two nuts on the element. Took out old part. Put new part in and reversed procedure. Works fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Laingsburg, MI
- Parts Used:
- WP99002560
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No water would enter in dishwasher
Removed covers on the bottom of dishwasher so I could get access to area. Measured no voltage on water inlet pump. removed to wires from foat switch, one screw to remove float switch. When I pressed the float switch button to activate the switch would not move. Ordered and replaced the switch. 30 minutes tops
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- serafino from oakland, MI
- Parts Used:
- 99002254
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dishwasher would not turn on
Once I removed the inside panel from the door replacing the switch was pretty simple. completed the job in less than twenty minutes.
This was the third appliance I have repaired with the help of Parts Select in the last three months.
This was the third appliance I have repaired with the help of Parts Select in the last three months.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ted from portland, OR
- Parts Used:
- W10131752
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Leaking water at bottom left of dishwasher door
Initially thought this issue was the dishwasher door gasket, but after reading post on this site about door latch grommet, removed 7 "hex screws" pulled inside of dishwasher door away and traced water from leak back to soap dispenser latch/grommet area so instead of ordering door gasket ordered door latch and grommet. Replaced grommet only (in addition to 7 "hex screws" had to remove 2 additional screws to get to it) which took some maneuvering. Re-aligned grommet and latch, inserted and tightened all screws that had been removed. Works great - no more water leaking!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jerry from wilton, CT
- Parts Used:
- WP902894
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Door leaked from lower right corner
First I replaced the soap door grommet -- door still leaked. Then I went for the really expensive part ($40) -- the door gasket. The old one came right out and the new one went right in -- 15 minutes tops -- and the door no longer leaked.
Thanks to all the previous posters for their hints.
Thanks to all the previous posters for their hints.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from ROCHESTER, MA
- Parts Used:
- WPW10117748
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
leaking door
easy repair. The foam has to go over some wires but if you stretch it alittle as you place it all goes well
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brad from York, ME
- Parts Used:
- WP902899
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dispenser door would not open
Attempted repair was quick & simple. Removed 7 torx screws, and then pulled the wax motor out of its holder. Pulled 2 wires off, and replaced old motor with new motor. Reattached wires, & reassembled.
Only problem was this did not fix the problem, so back to square one, but worth a shot.
Only problem was this did not fix the problem, so back to square one, but worth a shot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clifford from Palm Harbor, FL
- Parts Used:
- WP99002560
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Dishwasher would not fill with water
Remove the lower panel by taking out the 2 screws on top and 2 at the bottom of the panel. To diagnose the problem, verify that there is water supplied from the valve under the sink to the water supply valve under the DW. This can be done by turning off the valve under the sink, disconnecting the copper supply line under the DW then turning on the valve under the sink to see if water passes through the line.
The float switch is located on the left front (as you face the DW). This is activated by the float in the tub. Check to be certain that the float is not restricted. The contact point on the switch is a spring loaded plunger. It should depress as the float rises and pop back out as the float returns to its low point.
Turn off the circuit breaker for the DW. To remove the switch, pull off the two electric leads from the switch. Mark the top lead with a piece of tape. Then remove the one philips screw. Replace the switch by reversing the procedure. Note that you have aligned the float contact point with the float.
The float switch is located on the left front (as you face the DW). This is activated by the float in the tub. Check to be certain that the float is not restricted. The contact point on the switch is a spring loaded plunger. It should depress as the float rises and pop back out as the float returns to its low point.
Turn off the circuit breaker for the DW. To remove the switch, pull off the two electric leads from the switch. Mark the top lead with a piece of tape. Then remove the one philips screw. Replace the switch by reversing the procedure. Note that you have aligned the float contact point with the float.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Whitinsville, MA
- Parts Used:
- WP902894
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Leaky door
Removed old gasket and simply replaced it with the new one. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from goffstown, NH
- Parts Used:
- WP902894
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
washing machine leaked at right lower corner
removed old deteriorated gasket - just pulled out
cleaned soap particles from door seal area
pressd in new gasket - note orientation
done.
still leaks - will investigate further
cleaned soap particles from door seal area
pressd in new gasket - note orientation
done.
still leaks - will investigate further
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernadette from Glen Cove, NY
- Parts Used:
- WP902894
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
leak at bottom left and right side
pulled out the old gasket, cleaned the area before pressing in the new gasket with my fingers ,I made sure to put it in the same way as the old one. You have no idea how happy I am that this solved the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from Terre Haute, IN
- Parts Used:
- WP902894
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My dishwasher was leaking from the bottom right hand corner.
I removed the original gasket, wiped down the area, and installed the new gasket the same way the old one was installed. It was very easy.
Was this instruction helpful to you?
Thank you for voting!