CDB7000AWS2 Magic Chef Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Derek from ROCKFORD, MI
- Parts Used:
- WPW10348269
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Dishwasher Not Draining
The video included with this part is perfect. Unplug the dishwasher, take off the front trim piece, remove the drain hose from the pump, unclip the power, press the little clip that holds the pump in while turning it counter clockwise to remove. Then just do that in the opposite order to put the new one in. Just make sure you hear it click when you twist the new one on so you know the clip has engaged. Super easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from HIGGINSVILLE, MO
- Parts Used:
- WP8269145
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken Mounting bracket
Removed old part and replaced with new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LINDA from ROSEVILLE, CA
- Parts Used:
- WP8268961
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The door had no resistance when opening it
You only need to pull it out about 6 to 8 inches and you don’t need to disconnect anything to slide it on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from GRANDVIEW, MO
- Parts Used:
- W10648041
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
washer filled in when off..
replaced the valve
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Geoff from Avon, CT
- Parts Used:
- WP8268433
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
lack of water flow
removed rack
removed one screw
removed old seal
installed new seal
installed screw
removed one screw
removed old seal
installed new seal
installed screw
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dwight from KENT, WA
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
One of the old stops broke
Snapped the new stops on. It took about 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Giorgio from Savannah, GA
- Parts Used:
- 8269144A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench set
Drain hose broken.
Removed the old hose, after loosing metal looking rings. Installed new hose ad finally tight firmly the looking rings, using wrench and socket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Daleville, AL
- Parts Used:
- W10518394
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
The dishwasher would not dry (heat)
First I identified the problem by checking the plug ends of the heater coil with an ohm meter. I quickly odered the part and when it arrived a few days later, I simply pulled off the electrical connectors, unscrewed the two bolts, removed the old/broken coil, put in the new coil and tightened down the nuts snuggly.
Nothing to it. I then had to reset the error code and it is working like new.
Nothing to it. I then had to reset the error code and it is working like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eva from Shalimar, FL
- Parts Used:
- W10518394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Heater element broken
I removed the lower front panel of the dishwasher to expose wheels and opened door and removed two screws holding washer to cabinet. After raising leveling feet pulled washer out to expose bnotton ow dishwasher. Removed the electrical wires form the heating element and removed screw caps holding the heaqting element in place. Removed the old element and inserted the new, then reversed process to get it back together. It was very easy to do following the instructions I received when I ordered the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- eugene from REVERE, MA
- Parts Used:
- WP8268961
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
door would fall down when unlatched
Removed the bottom plate/cover. Unscrew top from bracket. Lucky,had just enough room to pull washer out. Only 6 in. Sleeve had broken off. Needle nose plyers to unhook spring. Slide sleeve over hinge. Hard Part///. Pull spring back into place. with door shut. good luck.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from FORT MYERS, FL
- Parts Used:
- WPW10348269
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Dishwasher would not drain properly due to broken impeller in the pump. Could hear and feel vibration thru pump body.
Followed the easy how-to video from PS. It was as easy as changing a light bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reid from ALPHARETTA, GA
- Parts Used:
- WPW10337934, W10518394
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dishes were not drying properly
Did the repair, but needed one extra step not described in video:
I followed the directions on the PartSelect Youtube video - very helpful! I do believe the heating element was the original culprit, as it had a "burn" area about the size of a dime that caused it to almost break into two parts. Obviously a point of failure.
BUT - after replacement, it still did not solve the problem of the dishes not drying.
After much web searching, I tried the diagnostic mode on the dishwasher, and that did a hard reset of the logic board and FIXED the problem.
So in all, it required both a new heating element AND a hard reset via diagnostic mode.
I followed the directions on the PartSelect Youtube video - very helpful! I do believe the heating element was the original culprit, as it had a "burn" area about the size of a dime that caused it to almost break into two parts. Obviously a point of failure.
BUT - after replacement, it still did not solve the problem of the dishes not drying.
After much web searching, I tried the diagnostic mode on the dishwasher, and that did a hard reset of the logic board and FIXED the problem.
So in all, it required both a new heating element AND a hard reset via diagnostic mode.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frances from Longmeadow, MA
- Parts Used:
- W10542314
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
worn gasket was fraying at bottom of door, leaking
just pulled old gasket out. New gasket took 2 attempts to fit in properly, but simple to do. Very easy to press into groove. Fit like a glove! Website drawings made choosing part very easy, thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Briant from Byron, MN
- Parts Used:
- 4317824
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
There was no problem
I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois from HUDSON, NC
- Parts Used:
- WPW10348269
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
pump not working
Looked on you-tube and it was so easy. Pump on bottom right. unplug pump and do a halfway turn. Plug the new one up and place the pump on, and turn halfway and its on. START your dishwasher
Was this instruction helpful to you?
Thank you for voting!