DU2J-CAN Magic Chef Dishwasher - Instructions

Pride old gasket out with screw driver easily removed it cleaned where the gasket was with mild detergent and easily installed new gasket

Remove lower cover, 4 Phillips screws. Remove bracket with float switch, two hex head screws in the rear. After removal pull switch wires, two in plastic housings. Remove float switch, one small Phillips head screw. Remove float switch lever, one Phillips head screw. Clean the bracket and lever. Replace the lever and lube with silicone. Replace the float switch, (new one) and replace wires. Reinstall install bracket with original hex head screws. Replace lower cover. Done.

The time to hook up the spring was a minute or two. I simply attached the linkage to the door and then attached the spring to the linkage.The extra time in the repair was re-attaching the cover.

Video on website made the repair easy

I first replaced the seal/grommet around the soap dispenser latch, which was leaking, but did not totally stop the leak. I ended up ordering the door gasket too. Both were very easy to replace. My wife wanted a new dishwasher, but let me take a crack at fixing the leak first. Woo Hoo - big $$$ saved.

The problem would rarely happen if the dishwasher was fully loaded vs. lightly loaded; which would produce a lot of water rapidly during the spray cycles. (or empty during the house inspection!). Removing and replacing the door gasket is super-easy.

Un screwed the dishwasher from the underside of my kithcen counter. Removed the copper water hose(after turning off water valves). PUlled the dishwasher from under counter to expose the hinges. Hung the new linkage on the hinge. Stetched the spring from flange on the bottom of the dishwasher to the new linkage. Reattached hose and reconnected the unit to counter top. Job done.

They just snapped in to place. Once I realized where they went. They are not the exact rollers needed but will do until I get the right ones. The rack will not come out as far as it should because of the difference. Other than that....easy.

At first I tried putting the spring into the lid where the shorter extension of the spring fit tightly into the recessed part of the lid. (If you look at the lid where the hole is for the spring and pin, you see that there is what looks like the arm of the letter "Q".) This worked, but the lid would only open with limited force and would hang down when the dishwasher door was closed.
After looking at it again, I positioned the spring so that the shorter extension of the spring ran through the partially open portion of the spring hole. (Looking at the cup laying flat on the ground, you see that the bottom of the pin/spring hole has a slit in it). This allowed the spring to have greater tension and I have had no more problems. The lid opens with force and stays closed when the dishwasher door is closed (vertical).
This may be a little confusing as I do not know the technical terms for any of this stuff, but I just mess with stuff til it works or breaks, whichever comes first! haha

My husband removed the screws that hold the inside panel in place to expose the contral panel area. He disconnected the wire connections and removed the part to replace. One of the relay housings cracked and he had to glue it back together before he could reassemble the whole thing. I did not include drying time in the repair time estimate. After reassembly, the dishwasher worked like a charm.
Many thanks to PartSelect.com and my husband!

With watching Video on line it was fairly simply, my son knew exactly what to do, it took him about 20 minutes from start to completion and when tested, dishwasher ran great. We have used it six times and have not had a problem. I would highly recommend this part if you are having the same problem. The video was very good.

After checking out the mechanism, I realized that the wax motor which operates the dispenser was no longer working. I conatacted Part select and on the second day, on a Saturday, Fedex delivered the little wax motor. I simply separated the front panel with the inside panel with 7 screws and a 1/4 inch nut driver. I slipped out the old wax motor, unclipped the two wires and slipped in the new motor. Attached the wires and put the panels back togehter. Voila, the dispenser works perfectly.
Total time, 15 minutes.

I removed the inside panel. This exposed the rear of the control panel. I carefully replaced the defective switch. Only one was bad but of course i replaced both.

From other comments on this site, I learned that 2 people fixed the problem with a new door gasket; 3 fixed the problem by replacing the dispenser latch. I tried the gasket and it helped some (obviously needed replacement anyway) but then learned that the rubber boot around the soap dispenser latch was torn into two pieces. Replaced it and good-to-go.

I pulled the unit out its bay and saw that one spring was missing. I looked up the parts online and ordered replacement springs and linkages. Using the existing spring and linkage as models, I easily installed the new parts. I ordered spare parts in case the other linkage broke.