DU2100B Magic Chef Dishwasher - Instructions

The dishwasher was running perfectly, but over time it leaked more and more. We were ready to throw it out, when I searched the internet and saw stories about a tiny gasket commonly failing. I couldn't believe that could be the trouble, but ordered the $3.75 part. Unscrewed the door, slipped out the old gasket and slipped on the new one. Screwed the door back. And the result? THE LEAK IS FIXED! Unbelievable. The old gasket had gotten stiff, probably exposure to soap, and it wasn't sealing properly. That $3.75 part saved us hundreds and hundreds of dollars and will give us extra years of use from our dishwasher.

After pulling dishwasher out both springs easily installed using plastic connectors on the bottom left and right sides. Pliars were used to stretch the springs. It took fifteen minutes at most.

Took the handle off the old basket and put it on the new one and it was done.

just unscrew the inside panel. using a torx screw driver. disconect vericarefully the bad actuator and install a new one. put back everything in back order .

Ordered 3 parts first ..all came within two biz days..forgot the toe panel, called it was here the next day! The people that assisted me were wonderful! My husband did the repair. the dishwasher looks like new!!!!! I will order from Part Select again and again...extremley pleased. Now if only we could cover the Refrigerator in Black it would look like a whole new kitchen!

removed lower dish basket. then removed 3 screws lifted element cover and removed center hold down nut lifted spray nozzle nad installed new parts. dishwasher is working like new.
thanks for asking.

Pulled out the old gasket and pressed in the new one. No more leakage.

I used a voltmeter to see if 120 volts was present at the right time in the cycle; it was, so the actuator was the likely culprit. I ordered one on a Monday afternoon about 2:30, and it appeared on my doorstep Tuesday, shortly after noon! It took less than 15 minutes to replace the actuator - removing the 7 Phillips-head screws, lifting the panel, popping out the upper actuator, removing the two wires, putting them on the new actuator, popping it in and putting the panel back on. Worked like a charm. Happy wife . . .

Remove screws holding the inside of the door. Set lid aside. Pull out the old foam insulation. Clean the area. Replace with new foam insulation. Put door back together.

Popped off the plactic screen filter (3 screws). Droped in the new Spary Arm and put back together.

You guys are AWESOME! I ordered the part on a Wednesday afternoon and received it Thursday morning. So all and all I didn't even have to wash any dishes by hand.

romoved 3 screws, removed spray arm support nut. pulled off spray arm support, replaced new spray arm support and spray arm support nut

My son was able to take the inside panel off to access area for handle to be replaced. A removal of approximately 12 screws and a little glue to glue felt pads in place VIOLA all fixed! Love this dishwasher so quiet and not ready to give it up.

I pulled out the old gasket and put in the new one. You need to stretch it a bit as you guide it in the track.
It was very easy but did not solve the problem.
Apparently, Maytag dishwashers are known for a leaky soap dish which I figured out after the door gasket was replaced. The problem is usually with the soap dish latch. You need to take the inner door off, disassemble the soap diehs, out a new gasket and latch on, reassemble, and you should be all set.

first i unhooked the 2 hoses then removed the 2 screws holding the valve in place, I then removed the hose fitting from the old unit and installed it on the new one. I then bolted on the new valve and reconnected the hoses and it worked fine.

Assumed that the door gasket needed replacing so I went to Partselect.com. Ordereed the gasket and was about to check out when I noticed the comments from others. Decided to look and was glad I did! Almost everyone said that the gasket on the soap dipenser latch on their door gasket repair was bad also so I ordered the latch gasket too. Parts arrived in only two days. I was amazed.
I started by turning the power off at the panel box, then removing the door gasket and cleaning the gasket groove. Then it was a simple matter of pushing the gasket into place, avoiding stretching or compressing it. Removing the gasket and putting in the new one was only about 3 minutes work - however cleaning the groove took somewhat longer. Then unscrewed the 7 torex screws on the interior door plastic panel. Carefully work the panel free, study the solenoid to see how it pops out and it attached, remove the solenoid and the panel is free of the door.
Examine the interior workings of the soap dispenser to see how it all fits. The remove the two hex head screws with a nut driver and carefully remove the assembly. Notice how the latch gasket fits with its boot in the notch on the latch base. The old boot was completely torn from the gasket base on mine. I cleaned accumulation of soad and crud from the mechanism and from the interior side of the door panel. Put it all back together in reverse order. The cleaning took longer thna the actual repairs.
Thank goodness for the comments - saved me a ton of aggravation!!! Partselect.com rules!