DU4J-C Magic Chef Dishwasher - Instructions

just unscrew the inside panel. using a torx screw driver. disconect vericarefully the bad actuator and install a new one. put back everything in back order .

romoved 3 screws, removed spray arm support nut. pulled off spray arm support, replaced new spray arm support and spray arm support nut

Remove screws holding the inside of the door. Set lid aside. Pull out the old foam insulation. Clean the area. Replace with new foam insulation. Put door back together.

Pulled out the old gasket and pressed in the new one. No more leakage.

Popped off the plactic screen filter (3 screws). Droped in the new Spary Arm and put back together.

You guys are AWESOME! I ordered the part on a Wednesday afternoon and received it Thursday morning. So all and all I didn't even have to wash any dishes by hand.

I pulled out the old gasket and put in the new one. You need to stretch it a bit as you guide it in the track.
It was very easy but did not solve the problem.
Apparently, Maytag dishwashers are known for a leaky soap dish which I figured out after the door gasket was replaced. The problem is usually with the soap dish latch. You need to take the inner door off, disassemble the soap diehs, out a new gasket and latch on, reassemble, and you should be all set.

I used a voltmeter to see if 120 volts was present at the right time in the cycle; it was, so the actuator was the likely culprit. I ordered one on a Monday afternoon about 2:30, and it appeared on my doorstep Tuesday, shortly after noon! It took less than 15 minutes to replace the actuator - removing the 7 Phillips-head screws, lifting the panel, popping out the upper actuator, removing the two wires, putting them on the new actuator, popping it in and putting the panel back on. Worked like a charm. Happy wife . . .

Removed dishwasher door liner and removed soap dish door latch assembly. Removed latch from assembly and replaced with new latch. Had trouble replacing assembly in correct sequence. Had to go on line and look at sequence picture to replace assembly correctly. Installed new gasket and replaced liner in door. The new gasket and latch solved my leak problem.
Thank you PartSelect

Ordered 3 parts first ..all came within two biz days..forgot the toe panel, called it was here the next day! The people that assisted me were wonderful! My husband did the repair. the dishwasher looks like new!!!!! I will order from Part Select again and again...extremley pleased. Now if only we could cover the Refrigerator in Black it would look like a whole new kitchen!

The dripping water was coming from bottom right side of the door, almost directly beneath the detergent dispenser. Looking closely at the drips, I could see that they were coming from saturated insulation that is between the inner and outer door layers. I took the inside piece of the door apart and sure enough I could see water had been getting through the door latch and running down the inside of the door. I could see that the grommet around the door latch was cracked and brittle, so I replaced it and was pretty sure that would resolve the problem. But when I put the door all back together and did a test run, I had a leak even bigger than the first, but this leak appeared to be through the door seal at the bottom right. I then ordered a new door seal, which took only 5 minutes to replace and resolved the leak. I think the old door seal was too worn out at that spot and just by removing and replacing the inside door layer, it must have not made a good seal at that point. But I recommend starting with the door latch and grommet first, since that is a $4 part, and then proceeding with the door seal, a $43 part, only if necessary.

removed lower dish basket. then removed 3 screws lifted element cover and removed center hold down nut lifted spray nozzle nad installed new parts. dishwasher is working like new.
thanks for asking.

USED A STAR SCREWDRIVER TO REMOVE THE LOWER SCREEN THEN REMOVED THE SUPPORT NUT BY HAND REPLACED THE LOWER SPRAY ARM & SCREEN WORK BETTER THAN EVER.THE ONLY NEGATIVE WAS THE PART TOOK 10 DAYS TO ARRIVE .

Kill power to unit. Lower door. Hold down door and remove inner plastic door cover torx screws, rotate up and use inner door cover to brace outer spring loaded door from closing. lift off metal strap that runs along top edge of door. Unsnap black plastic cover.Latch is under cover. Unplug wires with pliers (they just pull off) after noting where they go. Unscrew single hex head screw and remove latch assembly. inside latch will be reused with the new latch switch holder. Pry up plastic clip keepers and remove inside latch. Depending on age they might break, no big deal you will use the new holder anyway. orient and install switches into holder, install inner latch and install assembly back onto door. Install wires, cover, metal strip and inner door in reverse order. Very easy to do. Parts worked perfect.

Video on website made the repair easy

I removed the gasket from around the dishwasher. Cleans the grove of any dirt, mold or other debris. I started the gasket replacement at the top center of dishwasher by folding the gasket in half to find the center and inserting that center point into the grove just below the latch.i then inserted the rest of gasket with my thumb into the remaking grove first to the right corner then to the left. No told were needed leak was gone