DU4J Magic Chef Dishwasher - Instructions

Kill power to unit. Lower door. Hold down door and remove inner plastic door cover torx screws, rotate up and use inner door cover to brace outer spring loaded door from closing. lift off metal strap that runs along top edge of door. Unsnap black plastic cover.Latch is under cover. Unplug wires with pliers (they just pull off) after noting where they go. Unscrew single hex head screw and remove latch assembly. inside latch will be reused with the new latch switch holder. Pry up plastic clip keepers and remove inside latch. Depending on age they might break, no big deal you will use the new holder anyway. orient and install switches into holder, install inner latch and install assembly back onto door. Install wires, cover, metal strip and inner door in reverse order. Very easy to do. Parts worked perfect.

Video on website made the repair easy

I removed the gasket from around the dishwasher. Cleans the grove of any dirt, mold or other debris. I started the gasket replacement at the top center of dishwasher by folding the gasket in half to find the center and inserting that center point into the grove just below the latch.i then inserted the rest of gasket with my thumb into the remaking grove first to the right corner then to the left. No told were needed leak was gone

With watching Video on line it was fairly simply, my son knew exactly what to do, it took him about 20 minutes from start to completion and when tested, dishwasher ran great. We have used it six times and have not had a problem. I would highly recommend this part if you are having the same problem. The video was very good.

Just slide the old upper dishrack forward to the end. The stops on either slide must be removed . Only difficulty was getting the plastic stops to open up. We used a thin metal knivre to wedge into the opening.

Took off the lower front plastic piece and unscrewed the side panel to snap the new part in place then attached the spring to it.

The time to hook up the spring was a minute or two. I simply attached the linkage to the door and then attached the spring to the linkage.The extra time in the repair was re-attaching the cover.

Remove lower cover, 4 Phillips screws. Remove bracket with float switch, two hex head screws in the rear. After removal pull switch wires, two in plastic housings. Remove float switch, one small Phillips head screw. Remove float switch lever, one Phillips head screw. Clean the bracket and lever. Replace the lever and lube with silicone. Replace the float switch, (new one) and replace wires. Reinstall install bracket with original hex head screws. Replace lower cover. Done.

From other comments on this site, I learned that 2 people fixed the problem with a new door gasket; 3 fixed the problem by replacing the dispenser latch. I tried the gasket and it helped some (obviously needed replacement anyway) but then learned that the rubber boot around the soap dispenser latch was torn into two pieces. Replaced it and good-to-go.

I removed the inside panel. This exposed the rear of the control panel. I carefully replaced the defective switch. Only one was bad but of course i replaced both.

Turned off the water. Disconnected the water supply line. Extracted 2 screws holding the dishwasher. Pulled out the dishwasher. Changed out the nylon spring link. Pushed the dishwasher back into place. Reattached the water line. Turned the water back on.

Spring linkage and postage about $15.00.
Savings on service call and parts about $175.00. What a deal. Thank you PartSelect.

I took off the pump cover, removed the broken part. The support was broken at the threaded area so I needed to remove both pieces. Then I just used the diagram to see how all the pieces fit back together. I always take a picture too just in case I don't remember how it should go back.

Super easy repair.

They just snapped in to place. Once I realized where they went. They are not the exact rollers needed but will do until I get the right ones. The rack will not come out as far as it should because of the difference. Other than that....easy.

Removed front access panel
Disconnected water supply
Pulled dishwasher out approximately 1 foot to gain access to spring linkage
Connected new spring linkage to spring, connected other end of spring linkage to door
Tested operation of door
Slid dishwasher back into place, reconnected water supply and front access panel

At first I tried putting the spring into the lid where the shorter extension of the spring fit tightly into the recessed part of the lid. (If you look at the lid where the hole is for the spring and pin, you see that there is what looks like the arm of the letter "Q".) This worked, but the lid would only open with limited force and would hang down when the dishwasher door was closed.
After looking at it again, I positioned the spring so that the shorter extension of the spring ran through the partially open portion of the spring hole. (Looking at the cup laying flat on the ground, you see that the bottom of the pin/spring hole has a slit in it). This allowed the spring to have greater tension and I have had no more problems. The lid opens with force and stays closed when the dishwasher door is closed (vertical).
This may be a little confusing as I do not know the technical terms for any of this stuff, but I just mess with stuff til it works or breaks, whichever comes first! haha