DU2JV Magic Chef Dishwasher - Instructions

Pulled out the old gasket and pressed in the new one. No more leakage.

removed the 2 stops that held in the upper basket. rolled the old one out and slid the new one in. the replaced the stops. cake and pie!!

just pulled out old gasket
pushed in new one

After reading repair stories on this website, I decided to order the grommet as well as the seal for my dishwasher door. The seal was easy, just pull the old one out and push the new one in. Make sure the ends were even and that was done. Next came the grommet. 7 screws and I had the plastic off of the door. Then you just flip the plastic panel over and be careful of the wires.(I didn't remove them) Remove two more screws and the latch came out. Just tug the old grommet off and push the new one into place. Line it back up and replace the bolts. Flip the plastic back over and put the other 7 screws back in and you are ready to clean again. While I was in there I took a little extra time to clean some of the buildup out of the sealing surfaces. No more leaks!

I removed the gasket from the packaging & soaked it in hot water for approx 5 minutes to enhance the pliability of the rubber. I them opened the dishwasher door and removed the existing gasket, making sure I observed any specifics of the gasket, (ie...shape of gasket). I then cleaned any debris from the gasket channel. I took the new gasket from the water and folded it in half to determine where the middle was, and I started inserting the gasket beginning at the middle area of the channel, (just under the door latching mechanism). I finished inserting both sides and then closed the door for approximately 30 minutes to complete the gasket seating process. No leaks!!!

Remove the old rack and slip in the new one. Took 5 min to figure out how to remove the upper rack. Now have "new" dishwasher. Great service by PartSelect.

watched the video instructions and followed them. ;Very easy.

popped the two end caps off of the runners (the hardest part of the installation was figuring out how to pop them without braking them). Turns out just using a flat screw driver to start opening the cap lock did the trick. Once the end caps were off it was just a matter of rolling the old one off and the new one on and then putting the end caps back on.

The new basket wasn't an exact match, it's lighter weight and doesn't have the exact same configuration as far as the rows of tines. This will do us fine until it's time to replace the unit.

The repair went great. Very simple process to remove the old gasket and just press the new one in by hand. Total time to repair was 3 minutes. This was a very easy process, only needed to use a screw driver and my fingers to do it. The water leak was over. Anyone can do this repair. Don't think about getting a new dishwasher, or a plumber, as this is a very
simple repair that will easily do the fix!

I removed the inside cover of the door (6 to 8 screws), disconnected the wiring and wrote down where they needed to plug back into. Slipped the new dispenser door latch grommet over the latch, re-connected the wires, laid the door's inside cover back into place and replaced the screws. No leaks since. I have to say that without the help on partselect.com I would have wasted time and money in replacing the door's gasket. I'll definately check back here when any problem arises.

Actually following the online video is the way to go.

Remove lower cover, 4 Phillips screws. Remove bracket with float switch, two hex head screws in the rear. After removal pull switch wires, two in plastic housings. Remove float switch, one small Phillips head screw. Remove float switch lever, one Phillips head screw. Clean the bracket and lever. Replace the lever and lube with silicone. Replace the float switch, (new one) and replace wires. Reinstall install bracket with original hex head screws. Replace lower cover. Done.

The time to hook up the spring was a minute or two. I simply attached the linkage to the door and then attached the spring to the linkage.The extra time in the repair was re-attaching the cover.

Replaced cup lid spring first no luck then replaced detergent cup motor problem fixed complete part replacement took less then 30 min.

Pride old gasket out with screw driver easily removed it cleaned where the gasket was with mild detergent and easily installed new gasket