LDS5040BB LG Dishwasher - Instructions

Saw a YouTube video that explained the problem was the pump. Removed dishwasher from under the counter, flipped it on its side, and unplugged the unit. Removed bottom cover and the pump is right there. Used pliers to lose and move 3 hose clamps. Unplugged 3 wires and unscrewed the ground. Unhooked rubber hold downs and removed. Installed new pump. Parts Select pricing was best I found and shipping was fast. Nice to have a quiet house again when running the dishwasher. Cost in total was less than $100.

This was my first time repairing a dishwasher. I watched YouTube on how to remove the dishwasher from the cabinet. Afterwards, I removed the bottom of the dishwasher while it was laying flat to get to the motor and micro switch. The only difficulty I had was getting to the motor which required taking the bottom section off of the dishwasher. I could not get an appliance repair company to work on an LG dishwasher. My only option was to repair the dishwasher or bought a new dishwasher. Therefore, my wife and I decided to , make an attempt to repair this one with a backup plan of buying a new one. Luckily, we were able to fix this one within two hours.

This was a $999 dishwasher. We saved the cost of a new dishwasher by taking the time to fix this one.

same as in the video , but the double red wire is on the wrong terminal you have to break the plastic housing on the dishwasher and put it on the first one next to the white wire .if you hook it up the way it is the dishwasher wont work and when you open the door the dishwasher turns on . watch the video real close when it gets to the wire connections you see the double red wire goes over one pin to the one next to the white wire . works fine after that.

Followed the video provided by your company, done like 1,2,3

I watched the video and it showed every step to remove the old part and replace the new one. Went fairly easy except when put the new motor in the new seal was difficult to put on. I think if I would taken off the front door I could have got close to the back of the rubber seal to secure it a little easier. Had to use a rubber hammer hold my breath to not brake the plastic motor. But that was only way I could get in. The video showed it going rely easy that was not the case because it was a new seal. In the end it all worked out.
Thanks for the video's to help

Simply took the old clips off and put the new ones in.
works like a charm.
very easy to install
I am very happy with the result.
The delivery and payment and ordering process was on point.
I would order from this company again!!

snapped on new axel-wheel assembly

Removed two screws (one each side) and the toe kick plate at the bottom. Slide the dishwasher out from the cabinets about 10", remove broken cord clip from door and spring. Install door clip and wrap cord around pulley , attach to spring then attach spring to door, lifting the door will help attach the spring. Do one side of the door at a time.

connector was broken. just attached new connector to spring on each side of door. easy fix.

Replaced it . Simple

These were a simple snap on item. It took longer to carry the parts from the porch that to install. Recently purchased house. Rollers were missing due to overload?? Removed the remaining roller pieces. Cleaned and straightened the axle shafts, spray lubed the tray and snapped the new pieces in place.

Turn off circuit breaker. Turn off water at shutoff valve usually located under sink. Disconnect water line from dishwasher. Disconnect wires for the power feed from cord, Marked corresponding wires upon removal for re-installation. Remove 2 mounting screws that secure dishwasher to counter. Slide dishwasher out from counter and turn upside down. Use a blanket to prevent scratching of surfaces. Locate component on the back portion of the dishwasher. Unplug 2 wiring harnesses. My part was held on by 2 phillip screws. One in front, the other in the back along the leg bracket support. Once removed, reverse the order of removal. The i a You Tube video you can locate fr this removal. They said that you needed to release a clip to get the part out. Mine had a screw holding it on the back side. This difference cause about an extra 1/2 hour before I was able to figure out that there was NO clip that was being shown on the video. After that, The replacement went smoothly and we were having the dishes washed later that day.

Was not able to see where the Stopper, Rollers ( Part # PS3523062) could be attached to the back of the bottom tray, to fix the problem. So the parts were useless.

I disconnected the power cord and the drain hose, with a nut driver, under the sink. I removed the bottom plate that covers the water connection under the dishwasher. With the water turned off I used an adjustable wrench to disconnect the water line. I open the door and disconnected the brackets under the counter top, with a phillips screwdriver, that hold the dishwasher in place. I pulled the dish washer out of its enclosure far enough to fully access the spring loaded mechanism to replace the "connector assembly". Then I put it all back where it belonged.. Go slowly and have patience.

Replace basket with new replacement. Ordering and shipment VERY EASY! I have used your service in the past and will continue to in the future. Shipments are fast and accurate.