LSDF995ST (ASTEEUS) LG Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ricardo from Gilbert, AZ
- Parts Used:
- 4933DD3001B
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door is to heavy to hold
The connector assembly connects to a spring to hold the door from falling down. You need to disconnect the power cord, the water line and the drain hose before you move the dishwasher out the kitchen counter. There are several screws that hols the dishwasher in place top, side and bottom. Removed all screws then pull the dishwasher out very slow. Take the side panel by un-screwing all the screws around the panel in my case where five screws (two in the front so you have to open the door to get to them). You need to keep the door down to connect the assembly to the door bracket and the go through the pulley then to the spring, very easy. Put the side panel back and push the dishwasher in place use the same screws and reconnect the hose the water line and the power and you are done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aleksander from Wheeling, IL
- Parts Used:
- 6913ER4001B
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Led lamp burnt out
Replaced them
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Jacksonville, IL
- Parts Used:
- MFZ32863101
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
There was not enough pressure on the sprayers to clean the dishes. found the pump gasket cut in two and out of place.
I disassembled the upper parts of the pump housing and installed the new gasket. It seems to work fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Camdenton, MO
- Parts Used:
- 4681ED1004B
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dish washer would shut off mid cycle.
Check the motor and discovered roughness when you turned the shaft. I assume there was a bearing problem. I ordered a new motor from part select and upon the replacement washer is working great! Thanks part select, my part arrived in a timely manner and you guys saved me approx. $500. Thanx again. Richard Sansom
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Ypsilanti, MI
- Parts Used:
- 5001DD4001A, 4933DD3001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Door lift assist broke
removing the dishwasher from under the counter I accidentally broke the mounting braket, to investigate/discover the door lift cord had frayed and broken. Parts were easy to locate and the costomer service was friendly. Installation was a breeze and perfectly intuitive. Not a Problem. thanks for being there, hiring a repairman would have been expensive.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Glenwood Springs, CO
- Parts Used:
- 4933DD3001B
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
door connector broke, so door just flopped open
pulled the dishwasher out, removed the side panel. It was very easy to replace the connector once the dishwasher was out and the side panel was removed. There are about five screws to remove the side panel. I replaced the unbroken connector on the other side since I had the dishwasher out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jill from Mishawaka, IN
- Parts Used:
- 4933DD3001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The connector that provides counter weight for the door snapped and the door would flop open, it weighs a lot
Undo screws holding dishwasher in place, two screw just inside door one each side, should be covered with plastic cap. Slide dishwasher out, there is a spring on each side of the door connected through the connector to the door and cabinet. Slide connector our, install new one, slide disher back in, reattach screws holding dishwasher in place and your done.
Was this instruction helpful to you?
Thank you for voting!