LDF8812ST LG Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Timothy from SUSANVILLE, CA
- Parts Used:
- 4581DD3003B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
lost old wheel
snapped on new axel-wheel assembly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from BREWER, ME
- Parts Used:
- 4933DD3001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Door return
Replaced it . Simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from Quinlan, TX
- Parts Used:
- 3750DD2002A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed to replace bad racks
Just popped the old ones out and popped the new ones in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Blair from POTTSTOWN, PA
- Parts Used:
- 4933DD3001B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Hinge Cables Broke (Both), AGAIN!!
Cables have broken about every 3-6 months after original ones broke after 8 years. Removed front kick plate screws and remove kick plate, and remove two top screws holding Dishwasher to counter-top. Pull dishwasher out about 10 inches. Remove all broken parts and replace cables. Side dishwasher back in place and reinstall removed screws. I just hope these Cables last longer than the ones I had bought from another source. I have replaced those Cables 5 times already and hope these last MUCH longer. Delivery was very fast from PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from GOLDSBORO, NC
- Parts Used:
- 4924FD2123E
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced rinse aid cap
All I needed was the rinse aid cap, damm shame one must pay $75 for for the complete rinse aid dispenser just to replace the cap. I will not purchase LG product again. The cost to just replace the cap is a rip-off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from FREDERICKSBRG, VA
- Parts Used:
- 4933DD3001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Dishwasher door would drop, cords were broken
Removed two screws (one each side) and the toe kick plate at the bottom. Slide the dishwasher out from the cabinets about 10", remove broken cord clip from door and spring. Install door clip and wrap cord around pulley , attach to spring then attach spring to door, lifting the door will help attach the spring. Do one side of the door at a time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tom from grass valley, CA
- Parts Used:
- 4975DD1001A, 3920DD3005A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Dishwasher leaks from door region during washing cycle.
Old door seal appeared ok, no rips and seated evenly all around. Pulled that seal out and replaced with new. Seated new door seal after wetting inserted lip. Tested...leak greatly reduced, but still dripping. Removed seal, placed a rubber rope (same rope used for screening) within the tub recess, then reseated new seal. leak ceased. Also replaced the reservoirs on the left side of the cabinet (guide assembly). Old reservoir had debris within so decided to replace. Used regular pliers for the 3 hose spring clamps underneath, and a pair of large neede nose pliers for the fill flange (regular thread).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from WAUWATOSA, WI
- Parts Used:
- 4581DD3003B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Two installed roller wheels came off and broke.
I ordered four wheels to replace the two that were broken and to have two as spares. The wheels are to be snapped onto the bottom of the lower basket. The new wheels broke upon being installed. My extra wheels came in handy. I put them in very hot water for a few minutes to soften the plastic. I put a little Vaseline on the post they were to be attached to. The wheels then slid on and snapped correctly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from N LITTLE ROCK, AR
- Parts Used:
- 4933DD3001B
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
The dishwasher door would fall open when opening if it wasn't lowered slowly.
I disconnected the power cord and the drain hose, with a nut driver, under the sink. I removed the bottom plate that covers the water connection under the dishwasher. With the water turned off I used an adjustable wrench to disconnect the water line. I open the door and disconnected the brackets under the counter top, with a phillips screwdriver, that hold the dishwasher in place. I pulled the dish washer out of its enclosure far enough to fully access the spring loaded mechanism to replace the "connector assembly". Then I put it all back where it belonged.. Go slowly and have patience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Fairfield, CT
- Parts Used:
- 5005DD1001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bottom of silverware basket was breaking
Replace basket with new replacement. Ordering and shipment VERY EASY! I have used your service in the past and will continue to in the future. Shipments are fast and accurate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John R. from Huachuca City, AZ
- Parts Used:
- MFZ32863101, ADQ32598202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Filter mesh clouged up
Remove line to top wash area. Then removed all screws and rubber seal . Then just back step. In about 30 mins. it was ready to run ,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sean from Canton, CT
- Parts Used:
- AEM69493807
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Leak in drain line
Uninstall dishwasher screws. Lay dishwasher on its side. Remove bottom plate. Remove old drain line. install new line. Test for leak. The trick was figuring out that I could only access the line through the bottom of the dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LES from GAINESVILLE, FL
- Parts Used:
- 6201EC1006T
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Unit would not start up
Conclusion was that either the control panel or the noise filter (an electrical fuse apparatus)was bad. Disconnected the water line, turned off power, and pulled unit out from cabinets. Determined that voltage was going into the noise filter (white harness) but almost no voltage coming out (red harness). Ordered noise filter. Hardest part was removing old noise filter from dishwasher frame without removing the whole unit from cabinet and turning upside down.One screw holds the part in the frame. With power off, I used a very small ratchet with phillips screw driver. Pried unit out with screw driver on side to the panel front. It has a retaining tab there.Installation was the reverse. Instead of putting screw back the way it was originally installed, I screwed it in from the outside of the frame. Much easier and just as solid. Tested unit with power on. Hooked up water line. Works great. Note: LG dishwahers have a high repair rate and that this part has a high failure rate. This LG unit was two years old. Never had to fix my 15 year old Sears dishwasher. It still works to this day. (I gave it to my daughter.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from Johnsville, CA
- Parts Used:
- 4681ED1004B, 5911ED3003A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench set
Lg code indicated a faulty motor
First, PartSelect is great!; fast,& accurate. 1. Inside the dishwasher: remove trays. Remove (A050) lower water sprayer from bottom by pulling up. Remove (F191) top sprayer assembly by pulling away from clip holders. Remove (M110) by removing the holding screws. This part cover the whole sump and has kind-of an open screen circling the unit. Now you will see the white plastic impeller (M120) which is attached the the motor with one Phillips head screw. WARNING. The Phillips head screw (holding the impeller in place) is a REVERSE THREADED SCREW. Turn the screw CLOCKWISE to remove it. Then remove the impeller from the motor shaft. Underneath and outside the washer: Remove the bottom plate. Finally remove the motor by unscrewing the four holding screws and electrical wiring.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Damascus, MD
- Parts Used:
- 6201EC1006T
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Washer will not power on
Disconnected power. Removed washer top; only 2 screws in back. Disconnected two wire connectors on Filter Assembly Circuit. Removed assembly; 1 screw. Installed new assembly, reconnected wires, and replaced washer top.
Was this instruction helpful to you?
Thank you for voting!