LDF9810ST LG Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- dennis4417 from Albuquerque, NM
- Parts Used:
- 3750DD2002A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
racks were rusted
parts were not exact match with original, even though ordered from schematic. had to bend the replacement part slightly so it would fit into holder pieces. this took about 10 minutes as I was trying to be careful not to break/cut the coating (which would then lead to rust again). Once the piece was bent, just snapped the rack into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John R. from Huachuca City, AZ
- Parts Used:
- MFZ32863101, ADQ32598201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Filter mesh clouged up
Remove line to top wash area. Then removed all screws and rubber seal . Then just back step. In about 30 mins. it was ready to run ,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jill from Mishawaka, IN
- Parts Used:
- 4933DD3001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The connector that provides counter weight for the door snapped and the door would flop open, it weighs a lot
Undo screws holding dishwasher in place, two screw just inside door one each side, should be covered with plastic cap. Slide dishwasher out, there is a spring on each side of the door connected through the connector to the door and cabinet. Slide connector our, install new one, slide disher back in, reattach screws holding dishwasher in place and your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ricardo from Gilbert, AZ
- Parts Used:
- 4933DD3001B
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door is to heavy to hold
The connector assembly connects to a spring to hold the door from falling down. You need to disconnect the power cord, the water line and the drain hose before you move the dishwasher out the kitchen counter. There are several screws that hols the dishwasher in place top, side and bottom. Removed all screws then pull the dishwasher out very slow. Take the side panel by un-screwing all the screws around the panel in my case where five screws (two in the front so you have to open the door to get to them). You need to keep the door down to connect the assembly to the door bracket and the go through the pulley then to the spring, very easy. Put the side panel back and push the dishwasher in place use the same screws and reconnect the hose the water line and the power and you are done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aleksander from Wheeling, IL
- Parts Used:
- 6913ER4001B
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Led lamp burnt out
Replaced them
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sean from Canton, CT
- Parts Used:
- AEM69493807
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Leak in drain line
Uninstall dishwasher screws. Lay dishwasher on its side. Remove bottom plate. Remove old drain line. install new line. Test for leak. The trick was figuring out that I could only access the line through the bottom of the dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from Johnsville, CA
- Parts Used:
- 4681ED1004B, 5911ED3003A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench set
Lg code indicated a faulty motor
First, PartSelect is great!; fast,& accurate. 1. Inside the dishwasher: remove trays. Remove (A050) lower water sprayer from bottom by pulling up. Remove (F191) top sprayer assembly by pulling away from clip holders. Remove (M110) by removing the holding screws. This part cover the whole sump and has kind-of an open screen circling the unit. Now you will see the white plastic impeller (M120) which is attached the the motor with one Phillips head screw. WARNING. The Phillips head screw (holding the impeller in place) is a REVERSE THREADED SCREW. Turn the screw CLOCKWISE to remove it. Then remove the impeller from the motor shaft. Underneath and outside the washer: Remove the bottom plate. Finally remove the motor by unscrewing the four holding screws and electrical wiring.
Was this instruction helpful to you?
Thank you for voting!