LD6105BB1 (ABPEEUS) LG Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Terry from SAINT LOUIS, MO
- Parts Used:
- AJH31248608
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
MY DISHWASHER WAS SQUEAKING WHEN RUNNING
I watched the video and it showed every step to remove the old part and replace the new one. Went fairly easy except when put the new motor in the new seal was difficult to put on. I think if I would taken off the front door I could have got close to the back of the rubber seal to secure it a little easier. Had to use a rubber hammer hold my breath to not brake the plastic motor. But that was only way I could get in. The video showed it going rely easy that was not the case because it was a new seal. In the end it all worked out.
Thanks for the video's to help
Thanks for the video's to help
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from GARDNERVILLE, NV
- Parts Used:
- 4681ED3001D
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Dishwasher was making loud grinding/buzzing noise
Saw a YouTube video that explained the problem was the pump. Removed dishwasher from under the counter, flipped it on its side, and unplugged the unit. Removed bottom cover and the pump is right there. Used pliers to lose and move 3 hose clamps. Unplugged 3 wires and unscrewed the ground. Unhooked rubber hold downs and removed. Installed new pump. Parts Select pricing was best I found and shipping was fast. Nice to have a quiet house again when running the dishwasher. Cost in total was less than $100.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from MIDDLETOWN, NJ
- Parts Used:
- 4027ED3002A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Door wouldn't close/lock wouldn't engage
Very easy repair. First remove all the screws from the inside of the door, making sure you support the outside part of the door with a pot under it on the floor. Pull the locker part out, remove wire connection with needlenose pliers, and install replacement part. Put door back together, and you're done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Canterbury, CT
- Parts Used:
- 4933DD3001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
door to dishwasher would not open slowly. would slam open
connector was broken. just attached new connector to spring on each side of door. easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from BREWER, ME
- Parts Used:
- 4933DD3001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Door return
Replaced it . Simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Leo, IN
- Parts Used:
- 4581DD3003C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken Roller On The Lower Tray.
These were a simple snap on item. It took longer to carry the parts from the porch that to install. Recently purchased house. Rollers were missing due to overload?? Removed the remaining roller pieces. Cleaned and straightened the axle shafts, spray lubed the tray and snapped the new pieces in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICHARD from MURRIETA, CA
- Parts Used:
- 4620ED3001C
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
BOTTOM TRAY OF DISHWASHER WOULD SLIDE ALL THE WAY OUT WITH NO STOP
Was not able to see where the Stopper, Rollers ( Part # PS3523062) could be attached to the back of the bottom tray, to fix the problem. So the parts were useless.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from N LITTLE ROCK, AR
- Parts Used:
- 4933DD3001B
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
The dishwasher door would fall open when opening if it wasn't lowered slowly.
I disconnected the power cord and the drain hose, with a nut driver, under the sink. I removed the bottom plate that covers the water connection under the dishwasher. With the water turned off I used an adjustable wrench to disconnect the water line. I open the door and disconnected the brackets under the counter top, with a phillips screwdriver, that hold the dishwasher in place. I pulled the dish washer out of its enclosure far enough to fully access the spring loaded mechanism to replace the "connector assembly". Then I put it all back where it belonged.. Go slowly and have patience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Ypsilanti, MI
- Parts Used:
- 5001DD4001A, 4933DD3001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Door lift assist broke
removing the dishwasher from under the counter I accidentally broke the mounting braket, to investigate/discover the door lift cord had frayed and broken. Parts were easy to locate and the costomer service was friendly. Installation was a breeze and perfectly intuitive. Not a Problem. thanks for being there, hiring a repairman would have been expensive.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Fairfield, CT
- Parts Used:
- 5005DD1001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bottom of silverware basket was breaking
Replace basket with new replacement. Ordering and shipment VERY EASY! I have used your service in the past and will continue to in the future. Shipments are fast and accurate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Jacksonville, IL
- Parts Used:
- MFZ32863101
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
There was not enough pressure on the sprayers to clean the dishes. found the pump gasket cut in two and out of place.
I disassembled the upper parts of the pump housing and installed the new gasket. It seems to work fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Glenwood Springs, CO
- Parts Used:
- 4933DD3001B
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
door connector broke, so door just flopped open
pulled the dishwasher out, removed the side panel. It was very easy to replace the connector once the dishwasher was out and the side panel was removed. There are about five screws to remove the side panel. I replaced the unbroken connector on the other side since I had the dishwasher out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Camdenton, MO
- Parts Used:
- 4681ED1004B
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dish washer would shut off mid cycle.
Check the motor and discovered roughness when you turned the shaft. I assume there was a bearing problem. I ordered a new motor from part select and upon the replacement washer is working great! Thanks part select, my part arrived in a timely manner and you guys saved me approx. $500. Thanx again. Richard Sansom
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dennis4417 from Albuquerque, NM
- Parts Used:
- 3750DD2002A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
racks were rusted
parts were not exact match with original, even though ordered from schematic. had to bend the replacement part slightly so it would fit into holder pieces. this took about 10 minutes as I was trying to be careful not to break/cut the coating (which would then lead to rust again). Once the piece was bent, just snapped the rack into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John R. from Huachuca City, AZ
- Parts Used:
- MFZ32863101, ADQ32598201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Filter mesh clouged up
Remove line to top wash area. Then removed all screws and rubber seal . Then just back step. In about 30 mins. it was ready to run ,
Was this instruction helpful to you?
Thank you for voting!