D1608WB (ABWEEUS) LG Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jon from GARDNERVILLE, NV
- Parts Used:
- 4681ED3001D
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Dishwasher was making loud grinding/buzzing noise
Saw a YouTube video that explained the problem was the pump. Removed dishwasher from under the counter, flipped it on its side, and unplugged the unit. Removed bottom cover and the pump is right there. Used pliers to lose and move 3 hose clamps. Unplugged 3 wires and unscrewed the ground. Unhooked rubber hold downs and removed. Installed new pump. Parts Select pricing was best I found and shipping was fast. Nice to have a quiet house again when running the dishwasher. Cost in total was less than $100.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from MIDDLETOWN, NJ
- Parts Used:
- 4027ED3002A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Door wouldn't close/lock wouldn't engage
Very easy repair. First remove all the screws from the inside of the door, making sure you support the outside part of the door with a pot under it on the floor. Pull the locker part out, remove wire connection with needlenose pliers, and install replacement part. Put door back together, and you're done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Canterbury, CT
- Parts Used:
- 4933DD3001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
door to dishwasher would not open slowly. would slam open
connector was broken. just attached new connector to spring on each side of door. easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from BREWER, ME
- Parts Used:
- 4933DD3001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Door return
Replaced it . Simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Leo, IN
- Parts Used:
- 4581DD3003C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken Roller On The Lower Tray.
These were a simple snap on item. It took longer to carry the parts from the porch that to install. Recently purchased house. Rollers were missing due to overload?? Removed the remaining roller pieces. Cleaned and straightened the axle shafts, spray lubed the tray and snapped the new pieces in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICHARD from MURRIETA, CA
- Parts Used:
- 4620ED3001C
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
BOTTOM TRAY OF DISHWASHER WOULD SLIDE ALL THE WAY OUT WITH NO STOP
Was not able to see where the Stopper, Rollers ( Part # PS3523062) could be attached to the back of the bottom tray, to fix the problem. So the parts were useless.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from N LITTLE ROCK, AR
- Parts Used:
- 4933DD3001B
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
The dishwasher door would fall open when opening if it wasn't lowered slowly.
I disconnected the power cord and the drain hose, with a nut driver, under the sink. I removed the bottom plate that covers the water connection under the dishwasher. With the water turned off I used an adjustable wrench to disconnect the water line. I open the door and disconnected the brackets under the counter top, with a phillips screwdriver, that hold the dishwasher in place. I pulled the dish washer out of its enclosure far enough to fully access the spring loaded mechanism to replace the "connector assembly". Then I put it all back where it belonged.. Go slowly and have patience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Ypsilanti, MI
- Parts Used:
- 5001DD4001A, 4933DD3001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Door lift assist broke
removing the dishwasher from under the counter I accidentally broke the mounting braket, to investigate/discover the door lift cord had frayed and broken. Parts were easy to locate and the costomer service was friendly. Installation was a breeze and perfectly intuitive. Not a Problem. thanks for being there, hiring a repairman would have been expensive.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Fairfield, CT
- Parts Used:
- 5005DD1001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bottom of silverware basket was breaking
Replace basket with new replacement. Ordering and shipment VERY EASY! I have used your service in the past and will continue to in the future. Shipments are fast and accurate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Jacksonville, IL
- Parts Used:
- MFZ32863101
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
There was not enough pressure on the sprayers to clean the dishes. found the pump gasket cut in two and out of place.
I disassembled the upper parts of the pump housing and installed the new gasket. It seems to work fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John R. from Huachuca City, AZ
- Parts Used:
- MFZ32863101, ADQ32598201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Filter mesh clouged up
Remove line to top wash area. Then removed all screws and rubber seal . Then just back step. In about 30 mins. it was ready to run ,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Poughkeepsie, NY
- Parts Used:
- 4581DD3002A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Broken guide wheels on top dishwasher rack
Pried old rollers with screwdriver. pushed (or 'pliered' new rollers, after straightening gudie pins, if necessary. One new roller broke a minute after installation, but I ordered extras because 6 odl rollers had alread broken), so we're OK for another year or so...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Euless, TX
- Parts Used:
- 5005DD1001B, 4581DD3002A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken roller axle rack clips
Be sure to order extra rolled with axles. The clips the snap on to the top rack are delicate and I broke two of them putting them in place. Be sure to snug them on slowly and carefully, it seems that the soap scum buildup on the rack creates additional friction. This friction makes you need to push the part on harder, and when you do it snaps on too hrs and one side of the clip will break off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kimberly from Penn Valley, CA
- Parts Used:
- 4581DD3002A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
upper rack wheels had regraded, cracked and fallen off
went online with model number, looked up appliance exploded view on your site and ordered parts. parts came the next day. second time we have ordered from you. you rock!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ricardo from Gilbert, AZ
- Parts Used:
- 4933DD3001B
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door is to heavy to hold
The connector assembly connects to a spring to hold the door from falling down. You need to disconnect the power cord, the water line and the drain hose before you move the dishwasher out the kitchen counter. There are several screws that hols the dishwasher in place top, side and bottom. Removed all screws then pull the dishwasher out very slow. Take the side panel by un-screwing all the screws around the panel in my case where five screws (two in the front so you have to open the door to get to them). You need to keep the door down to connect the assembly to the door bracket and the go through the pulley then to the spring, very easy. Put the side panel back and push the dishwasher in place use the same screws and reconnect the hose the water line and the power and you are done.
Was this instruction helpful to you?
Thank you for voting!