39232533 LG Dishwasher - Instructions

Was not able to see where the Stopper, Rollers ( Part # PS3523062) could be attached to the back of the bottom tray, to fix the problem. So the parts were useless.

Replace basket with new replacement. Ordering and shipment VERY EASY! I have used your service in the past and will continue to in the future. Shipments are fast and accurate.

I disconnected the power cord and the drain hose, with a nut driver, under the sink. I removed the bottom plate that covers the water connection under the dishwasher. With the water turned off I used an adjustable wrench to disconnect the water line. I open the door and disconnected the brackets under the counter top, with a phillips screwdriver, that hold the dishwasher in place. I pulled the dish washer out of its enclosure far enough to fully access the spring loaded mechanism to replace the "connector assembly". Then I put it all back where it belonged.. Go slowly and have patience.

Conclusion was that either the control panel or the noise filter (an electrical fuse apparatus)was bad. Disconnected the water line, turned off power, and pulled unit out from cabinets. Determined that voltage was going into the noise filter (white harness) but almost no voltage coming out (red harness). Ordered noise filter. Hardest part was removing old noise filter from dishwasher frame without removing the whole unit from cabinet and turning upside down.One screw holds the part in the frame. With power off, I used a very small ratchet with phillips screw driver. Pried unit out with screw driver on side to the panel front. It has a retaining tab there.Installation was the reverse. Instead of putting screw back the way it was originally installed, I screwed it in from the outside of the frame. Much easier and just as solid. Tested unit with power on. Hooked up water line. Works great. Note: LG dishwahers have a high repair rate and that this part has a high failure rate. This LG unit was two years old. Never had to fix my 15 year old Sears dishwasher. It still works to this day. (I gave it to my daughter.)

Disconnected power. Removed washer top; only 2 screws in back. Disconnected two wire connectors on Filter Assembly Circuit. Removed assembly; 1 screw. Installed new assembly, reconnected wires, and replaced washer top.

These were a simple snap on item. It took longer to carry the parts from the porch that to install. Recently purchased house. Rollers were missing due to overload?? Removed the remaining roller pieces. Cleaned and straightened the axle shafts, spray lubed the tray and snapped the new pieces in place.

Pried old rollers with screwdriver. pushed (or 'pliered' new rollers, after straightening gudie pins, if necessary. One new roller broke a minute after installation, but I ordered extras because 6 odl rollers had alread broken), so we're OK for another year or so...

The connector assembly connects to a spring to hold the door from falling down. You need to disconnect the power cord, the water line and the drain hose before you move the dishwasher out the kitchen counter. There are several screws that hols the dishwasher in place top, side and bottom. Removed all screws then pull the dishwasher out very slow. Take the side panel by un-screwing all the screws around the panel in my case where five screws (two in the front so you have to open the door to get to them). You need to keep the door down to connect the assembly to the door bracket and the go through the pulley then to the spring, very easy. Put the side panel back and push the dishwasher in place use the same screws and reconnect the hose the water line and the power and you are done.

Be sure to order extra rolled with axles. The clips the snap on to the top rack are delicate and I broke two of them putting them in place. Be sure to snug them on slowly and carefully, it seems that the soap scum buildup on the rack creates additional friction. This friction makes you need to push the part on harder, and when you do it snaps on too hrs and one side of the clip will break off.

went online with model number, looked up appliance exploded view on your site and ordered parts. parts came the next day. second time we have ordered from you. you rock!

pulled the dishwasher out, removed the side panel. It was very easy to replace the connector once the dishwasher was out and the side panel was removed. There are about five screws to remove the side panel. I replaced the unbroken connector on the other side since I had the dishwasher out.

Undo screws holding dishwasher in place, two screw just inside door one each side, should be covered with plastic cap. Slide dishwasher out, there is a spring on each side of the door connected through the connector to the door and cabinet. Slide connector our, install new one, slide disher back in, reattach screws holding dishwasher in place and your done.