D1435TB LG Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Larry from Jacksonville, IL
- Parts Used:
- MFZ32863101
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
There was not enough pressure on the sprayers to clean the dishes. found the pump gasket cut in two and out of place.
I disassembled the upper parts of the pump housing and installed the new gasket. It seems to work fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Glenwood Springs, CO
- Parts Used:
- 4933DD3001B
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
door connector broke, so door just flopped open
pulled the dishwasher out, removed the side panel. It was very easy to replace the connector once the dishwasher was out and the side panel was removed. There are about five screws to remove the side panel. I replaced the unbroken connector on the other side since I had the dishwasher out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jill from Mishawaka, IN
- Parts Used:
- 4933DD3001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The connector that provides counter weight for the door snapped and the door would flop open, it weighs a lot
Undo screws holding dishwasher in place, two screw just inside door one each side, should be covered with plastic cap. Slide dishwasher out, there is a spring on each side of the door connected through the connector to the door and cabinet. Slide connector our, install new one, slide disher back in, reattach screws holding dishwasher in place and your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John R. from Huachuca City, AZ
- Parts Used:
- MFZ32863101, ADQ32598202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Filter mesh clouged up
Remove line to top wash area. Then removed all screws and rubber seal . Then just back step. In about 30 mins. it was ready to run ,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sean from Canton, CT
- Parts Used:
- AEM69493807
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Leak in drain line
Uninstall dishwasher screws. Lay dishwasher on its side. Remove bottom plate. Remove old drain line. install new line. Test for leak. The trick was figuring out that I could only access the line through the bottom of the dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LES from GAINESVILLE, FL
- Parts Used:
- 6201EC1006T
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Unit would not start up
Conclusion was that either the control panel or the noise filter (an electrical fuse apparatus)was bad. Disconnected the water line, turned off power, and pulled unit out from cabinets. Determined that voltage was going into the noise filter (white harness) but almost no voltage coming out (red harness). Ordered noise filter. Hardest part was removing old noise filter from dishwasher frame without removing the whole unit from cabinet and turning upside down.One screw holds the part in the frame. With power off, I used a very small ratchet with phillips screw driver. Pried unit out with screw driver on side to the panel front. It has a retaining tab there.Installation was the reverse. Instead of putting screw back the way it was originally installed, I screwed it in from the outside of the frame. Much easier and just as solid. Tested unit with power on. Hooked up water line. Works great. Note: LG dishwahers have a high repair rate and that this part has a high failure rate. This LG unit was two years old. Never had to fix my 15 year old Sears dishwasher. It still works to this day. (I gave it to my daughter.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Damascus, MD
- Parts Used:
- 6201EC1006T
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Washer will not power on
Disconnected power. Removed washer top; only 2 screws in back. Disconnected two wire connectors on Filter Assembly Circuit. Removed assembly; 1 screw. Installed new assembly, reconnected wires, and replaced washer top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Leo, IN
- Parts Used:
- 4581DD3003B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken Roller On The Lower Tray.
These were a simple snap on item. It took longer to carry the parts from the porch that to install. Recently purchased house. Rollers were missing due to overload?? Removed the remaining roller pieces. Cleaned and straightened the axle shafts, spray lubed the tray and snapped the new pieces in place.
Was this instruction helpful to you?
Thank you for voting!